20-100pcs For PS5 Motherboard F7001 F7002, F7003 Minor Fuse Fixed No Power After BSOD

Current exact-variant stock, UK delivery and price have been checked.Availability is rechecked at checkout.AliExpress seller description:
PS5 Mainboard Fuse Repair Kit – F7001 F7002 F7003 F7501 – NEW
Professional Board-Level Replacement Fuses – Compatible with All PS5 Models
High-quality brand new replacement fuses designed specifically for PlayStation 5 motherboard repair.Ideal for diagnosing and repairing no power, short circuit, and blown fuse protection faults.⚠️ Important Compatibility Notice
F5401 and F5402 cannot replace F7001, F7002, F7003, or F7501.F7001, F7002, F7003, and F7501 cannot replace F5401 or F5402.These fuse types operate at different voltage and amperage ratings and are designed for different motherboard circuits.Always check the exact fuse code printed on your PS5 motherboard before purchasing.Incorrect installation or substitution may result in further motherboard [external link removed] practical repair scenarios, the F7001 fuse is primarily used to fix console issues characterized by a "total dead state" or "no response upon powering on." It forms a "trio" of standby protection components alongside F7002 and F7003.Specifically, replacing or repairing F7001 addresses the following typical fault symptoms:
1.Fixing "No response when pressing the power button" (No Power / No Beep)
This is the most common symptom of an F7001 failure.Symptom: After plugging in the power cord and pressing the PS5 power button, the console makes no sound (no "beep"), the indicator light does not turn on, and the fan does not spin; the console is essentially "bricked."
Repair Principle: When the PS5 is plugged in but not yet turned on, the motherboard must first establish 5V and 3.3V standby voltages to power the Southbridge IC and the power-on control circuitry.If F7001 blows, the 5V standby voltage is completely cut off, preventing the motherboard from receiving the "power-on" signal.2.Fixing "Blue light flashes once then turns off" or "Instant power-off"
Symptom: After pressing the power button, the console's blue light might flash extremely briefly (or a "beep" might be heard), followed immediately by a complete power-off; subsequent button presses yield no [external link removed] Principle: In some cases, when the motherboard attempts to switch from standby to startup mode, a severe short circuit in downstream circuitry causes an instantaneous surge that blows F7001.This results in the console triggering a forced power-off protection mechanism due to the loss of standby voltage feedback just as it begins to boot.🔍 Why does F7001 blow? (Key to troubleshooting)
Simply replacing F7001 is usually insufficient, as it rarely blows "without reason." It typically blows because one of the following components has developed a short circuit to ground:
Southbridge IC short circuit: The PS5 Southbridge IC (responsible for controlling USB, networking, system booting, etc.) is a primary consumer of the 5V/3.3V standby voltage.If the Southbridge chip burns out and shorts, F7001 will blow immediately to prevent a widespread fire on the motherboard.Standby Power Management IC (PMIC) or MOSFET breakdown: If the chip responsible for stepping down the main 12V supply to 5V (such as certain Panasonic or ROHM power management chips) suffers a breakdown, it can feed high current directly into the standby circuit, blowing the fuse.Filter capacitor breakdown: A surface-mount ceramic capacitor (MLCC) located downstream of F7001 shorts out due to aging caused by prolonged exposure to high temperatures.🛠️ Repair Recommendations
Before soldering in a new F7001 fuse, you must use a multimeter (in continuity/buzzer mode) to measure the resistance to ground on the downstream side of F7001 (the side facing away from the power source).If the multimeter emits a continuous beep (indicating resistance close to 0 ohms), the short circuit persists.Under no circumstances should you apply power at this stage; instead, you must first locate the fault—using techniques like the "burn-in" method or by systematically checking capacitors and the Southbridge—and resolve the short circuit.Only after the resistance returns to normal levels should you solder the new F7001 and power on the device.Selected seller option: Model: PS5 · 20 pcs