FIXONICBefore you begin
The iPhone 8 Plus earpiece speaker also performs double duty as a loudspeaker, providing stereo sound. If your earpiece speaker is acting up, follow this guide to remove and replace it.
Official iFixit API visual reference
Open the authorised source
iPhone 8 Plus Earpiece Speaker Replacement
The iPhone 8 Plus earpiece speaker also...
Apple iPhone 8 Plus
Moderate
30 minutes - 1 hour
Guide 111371
Licensed iFixit integration
This attributed iFixit guide is displayed through Fixonic's recorded commercial API permission. iFixit remains the independent source and author of the procedure.
Repair step
- Power off your iPhone before beginning disassembly.
- Remove the two 3.5 mm pentalobe screws from the bottom edge of the iPhone.
Mark your opening picks
Tape over any cracks
- Lay overlapping strips of clear packing tape over the iPhone's screen until the whole face is covered.
- If you can't get the suction cup to stick in the next few steps, fold a strong piece of tape (such as duct tape) into a handle and lift the screen with that instead.
Anti-Clamp instructions
- Pull the blue handle backwards to unlock the Anti-Clamp's arms.
- Slide the arms over either the left or right edge of your iPhone.
- Position the suction cups near the bottom edge of the iPhone just above the home button—one on the front, and one on the back.
- Squeeze the cups together to apply suction to the desired area.
Repair step
- Pull the blue handle forwards to lock the arms.
- Turn the handle clockwise 360 degrees or until the cups start to stretch.
- Make sure the suction cups remain aligned with each other. If they begin to slip out of alignment, loosen the suction cups slightly and realign the arms.
Repair step
- Heat an iOpener and thread it through the arms of the Anti-Clamp.
- Fold the iOpener so it lays on the bottom edge of the iPhone.
- Wait one minute to give the adhesive a chance to release and present an opening gap.
- Insert an opening pick under the screen when the Anti-Clamp creates a large enough gap.
- Skip the next three steps.
Repair step
- Use a hairdryer or prepare an iOpener and apply it to the lower edge of the iPhone for about 90 seconds in order to soften up the adhesive underneath.
Repair step
Repair step
- Pull up on the suction cup with firm, constant pressure to create a slight gap between the front panel and rear case.
- Insert an opening pick or other thin pry tool a few millimeters into the gap.
Repair step
- Slide your pick around the corner and up the left edge of the phone, moving towards the volume control buttons and silent switch, breaking up the adhesive holding the display in place.
- Stop near the top left corner of the display.
Screen information
Repair step
Repair step
Repair step
Repair step
Repair step
- Slide the display assembly slightly down (away from the top edge of the phone) to disengage the clips holding it to the rear case.
Repair step
- Open the iPhone by swinging the display up from the left side, like the back cover of a book.
- Lean the display against something to keep it propped up while you're working on the phone.
Battery Disconnection
- Remove four Phillips (JIS) screws securing the lower display cable bracket to the logic board, of the following lengths:
- Two 1.3 mm screws
- One 1.4 mm screw
- One 2.7 mm screw
Repair step
Repair step
- Use the point of a spudger to pry the battery connector up from its socket on the logic board.
- Bend the connector cable up slightly to prevent it from accidentally making contact with the socket and providing power to the phone during your repair.
Repair step
Repair step
Repair step
- Remove the two tri-point Y000 screws securing the bracket over the front panel sensor assembly connector:
- One 1.0 mm screw
- One 1.2 mm screw
Repair step
Repair step
Repair step
Repair step
- Remove the five Phillips screws securing the earpiece speaker bracket:
- Two 1.8 mm screws
- One 2.3 mm screw
- One 2.4 mm screw
- One 2.8 mm screw
Repair step
- Remove the earpiece speaker bracket.
Repair step
- Use the flat end of a spudger to lift the front-facing camera from its housing.
- Gently bend the camera ribbon cable to the side to clear the way to the earpiece speaker underneath.
Repair step
- Remove the earpiece speaker.