Home/ Repair guides/ iPhone 11 Pro Max Front-Facing Cameras Replacem…

Official iFixit API visual reference

iPhone 11 Pro Max Front-Facing Cameras Replacement

Use this guide to remove and replace the front...

Apple iPhone 11 Pro Max Moderate 1 - 2 hours Guide 129703

Licensed iFixit integration

This attributed iFixit guide is displayed through Fixonic's recorded commercial API permission. iFixit remains the independent source and author of the procedure.

Guide overview

Before you begin

Use this guide to remove and replace the front camera assembly (a.k.a. selfie cam) in an iPhone 11 Pro Max. Note that if you replace this part, Face ID will no longer work. This repair will restore a broken selfie cam to working order, but only Apple or an Apple “authorized” technician can restore Face ID.

Step 1

Remove the pentalobe screws

⌕

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Before you begin, discharge your iPhone battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.
Power off your iPhone before beginning disassembly.
Remove the two 6.7 mm-long pentalobe screws at the bottom edge of the iPhone.
Opening the iPhone's display will compromise its waterproof seals. Have replacement seals ready before you proceed past this step, or take care to avoid liquid exposure if you reassemble your iPhone without replacing the seals.

Step 2

Mark your opening picks

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

If inserted too far, an opening pick can damage your device. Follow this step to mark your pick and prevent damage.
Measure 3 mm from the tip and mark the opening pick with a permanent marker.
You can also mark the other corners of the pick with different measurements.
Alternatively, tape a coin to a pick 3 mm from the tip.

Step 3

Tape over any cracks

⌕

TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

If your iPhone has a cracked screen, keep further breakage contained and prevent bodily harm during your repair by taping over the glass.
Lay overlapping strips of clear packing tape over the iPhone's screen until the whole face is covered.
Wear safety glasses to protect your eyes from any glass shaken free during the repair.
If you can't get the suction cup to stick in the next few steps, fold a strong piece of tape (such as duct tape) into a handle and lift the screen with that instead.
If all else fails, you can superglue the suction cup to the screen.

Step 4

Screen information

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

To avoid damaging your screen in the next steps, note the following:
There's a plastic bezel on the underside of the screen. Your opening pick will go underneath this bezel.
There's a seam between the plastic bezel and the display panel. Don't insert your pick here or you'll damage the screen.
Sometimes the display panel separates from the bezel before you even get a chance to insert a pick. This may be unavoidable depending on the condition of the adhesive. In this case, you’ll most likely need to replace your entire screen.

Step 5

Anti-Clamp instructions

⌕

TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

The next three steps demonstrate the Anti-Clamp, a tool we designed to make the opening procedure easier. If you aren't using the Anti-Clamp, skip down three steps for an alternate method.
For complete instructions on how to use the Anti-Clamp, check out this guide.
Pull the blue handle backwards to unlock the Anti-Clamp's arms.
Slide the arms over either the left or right edge of your iPhone.
Position the suction cups near the bottom edge of the iPhone—one on the front, and one on the back.
Squeeze the cups together to apply suction to the desired area.
If you find that the surface of your iPhone is too slippery for the Anti-Clamp to hold onto, you can use tape to create a grippier surface.

Step 6

Repair step

⌕

TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide

View item

Pull the blue handle forward to lock the arms.
Turn the handle clockwise 360 degrees or until the cups start to stretch.
Make sure the suction cups remain aligned with each other. If they begin to slip out of alignment, loosen the suction cups slightly and realign the arms.

Step 7

Repair step

⌕

TOOL USED ON THIS STEP iOpener Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

Heat an iOpener and thread it through the arms of the Anti-Clamp.
You can also use a hair dryer, heat gun, or hot plate—but extreme heat can damage the display and/or internal battery, so proceed with care.
Fold the iOpener so it lays on the bottom edge of the iPhone.
Wait one minute to give the adhesive a chance to release and present an opening gap.
Insert an opening pick into the gap under the screen and the plastic bezel, not the screen itself.
If the Anti-Clamp doesn't create a sufficient gap, apply more heat to the area and rotate the handle a quarter turn.
Don't crank more than a quarter turn at a time, and wait one minute between turns. Let the Anti-Clamp and time do the work for you.
Skip the next three steps.

Step 8

Heat the lower edge of the phone

⌕

TOOL USED ON THIS STEP iOpener Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Heating the lower edge of the iPhone helps soften the adhesive securing the display, making it easier to open.
Use a hairdryer or heat gun or prepare an iOpener and apply it to the lower edge of the iPhone for about a minute in order to soften up the adhesive underneath.

Step 9

Repair step

⌕

TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide

View item

If you're using a single suction handle, apply it to the bottom edge of the phone, while avoiding the curved portion of the glass.

Step 10

Lift the display slightly

⌕

TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

Pull up on the suction cup with firm, constant pressure to create a slight gap between the front panel and rear case.
Insert an opening pick into the gap.
The watertight adhesive holding the display in place is very strong; creating this initial gap takes a significant amount of force. If you're having a hard time opening a gap, apply more heat, and gently rock the screen up and down to weaken the adhesive until you create enough of a gap to insert your tool.

Step 11

Separate the screen adhesive

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Slide the opening pick around the lower left corner and up the left edge of the iPhone, slicing through the adhesive holding the display in place.
Don't insert your pick more than 3 mm, as you may damage internal components.

Step 12

Screen information

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

There's a delicate cable along the right edge of your iPhone. Don't insert your pick here, as you may damage the cable.

Step 13

Repair step

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

Re-insert your pick at the bottom edge of the iPhone, and slide it up the right side to continue separating the adhesive.
Don't insert your pick more than 3 mm, as you may damage the display cables.

Step 14

Repair step

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

The top edge of the display is secured with both glue and clips.
Gently pull the right edge of the display down slightly (in the direction of the Lightning port).
Insert your pick into the top-right corner of the phone.

Step 15

Repair step

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

Continue pulling the display down (toward the Lightning port) as needed in order to make a gap large enough for the pick.
Slide the pick to the top left corner and cut any remaining adhesive securing the display.
Don't insert your pick more than 3 mm, as you may damage the front panel sensor array.

Step 16

Remove the suction cup

⌕

TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Pull on the small nub on the suction cup to remove it from the front panel.

Step 17

Open the iPhone

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

Open the iPhone by swinging the display up from the left side, like the back cover of a book.
Don't try to fully separate the display yet, as several fragile ribbon cables still connect it to the iPhone's logic board.
Lean the display against something to keep it propped up while you're working on the phone.
During reassembly, lay the display in position, align the clips along the top edge, and carefully press the top edge into place before snapping the rest of the display down. If it doesn't click easily into place, check the condition of the clips around the perimeter of the display and make sure they aren't bent.

Step 18

Unscrew the battery connector cover

⌕

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Remove two 1.3 mm long Y000 screws securing the battery cover bracket.
Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your iPhone.
During reassembly, this is a good point to power on your iPhone and test all functions before you seal the display in place. Be sure to power your iPhone back down completely before you continue working.

Step 19

Remove the battery connector cover

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

Remove the bracket.

Step 20

Disconnect the battery

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

Use a spudger or a clean fingernail to pry the battery connector up from its socket on the logic board.
Try not to damage the black silicone seal surrounding this and other board connections. These seals provide extra protection against water and dust intrusion.
Bend the connector slightly away from the logic board to prevent it from accidentally making contact with the socket and providing power to the phone during your repair.

Step 21

Unscrew the logic board cover screws

⌕

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Use a Y000 driver to remove six 1.3 mm screws securing the logic board cover bracket.

Step 22

Remove the logic board cover bracket

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

Remove the bracket.

Step 23

Disconnect the OLED display cable

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

Use a spudger or a fingernail to disconnect the OLED panel cable connector.
To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.

Step 24

Disconnect the front sensors + digitizer

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

Use a spudger or a fingernail to disconnect the front sensor assembly cable connector.
Use a spudger or a fingernail to disconnect the digitizer cable connector.
If any part of your screen doesn't respond to touch after your repair, disconnect the battery and then re-seat this connector, making sure it clicks fully into place and that there's no dust or other obstruction in the socket.

Step 25

Remove the display assembly

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

Remove the display assembly.
During reassembly, pause here if you wish to replace the waterproof adhesive around the edges of the display.

Step 26

Disconnect the Face ID hardware

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

Use a spudger or a fingernail to disconnect the Face ID dot projector and sensor cables from their sockets on the logic board.

Step 27

Disconnect the selfie cam

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

Gently push the Face ID cable connectors away from the logic board to access the selfie cam connector underneath.
Disconnect the selfie cam by prying its connector straight up.

Step 28

Repair step

⌕

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

Grasp the front camera assembly with tweezers, being careful not to get fingerprints on the sensors.
Slide the front camera assembly slightly down and to the left to free it from the enclosure.

Step 29

Remove the front-facing cameras

⌕

Remove the front-facing cameras.