FIXONIC
Repair starts here.Sign inCreate account Live auctionsRepair HubRepair guides
SellSavedMy Fixonic
FIXONICrepair marketplace
Home/ Repair guides/ iPhone SE 2022 Lightning Connector Assembly Rep…
Official iFixit API visual reference

iPhone SE 2022 Lightning Connector Assembly Replacement

Use this guide to remove or replace the...

Apple iPhone SE 2022 Moderate 1 - 3 hours Guide 150091
Open the authorised source
Licensed iFixit integration

This attributed iFixit guide is displayed through Fixonic's recorded commercial API permission. iFixit remains the independent source and author of the procedure.

Guide overview

Before you begin

Use this guide to remove or replace the Lightning connector assembly for the iPhone SE 2022. This assembly includes the lower microphones, an antenna converter cable, and the Lightning connector. If you've tried cleaning the lightning port to no avail, replacing the Lightning connector can solve charging and connectivity issues. This guide was performed on the A2783 (international) model. If you do not replace the adhesive seals when reassembling, your device will function normally, but will most likely lose its water protection. You’ll need replacement adhesive to reattach components when reassembling the device.

Step 1

SIM Card Tray Removal

iPhone SE 2022 Lightning Connector Assembly Replacement — SIM Card Tray Removal ⌕
SIM Card Eject Tool
TOOL USED ON THIS STEP SIM Card Eject Tool Referenced by the iFixit guide
View item
  • Insert a SIM card eject tool, a SIM eject bit, or a straightened paper clip into the hole on the SIM tray located at the right edge of the phone.
  • Press directly into the hole to eject the SIM card tray.
  • Remove the SIM card tray.
Step 2

Remove the pentalobe screws

iPhone SE 2022 Lightning Connector Assembly Replacement — Remove the pentalobe screws ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Power off your phone before beginning disassembly.
  • Remove the two 3.4 mm P2 pentalobe screws on the bottom edge of the iPhone.
Step 3

Mark your opening picks

iPhone SE 2022 Lightning Connector Assembly Replacement — Mark your opening picks ⌕
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • If inserted too far, an opening pick can damage your device. Follow this step to mark your pick and prevent damage.
  • Measure 3 mm from the tip and mark the opening pick with a permanent marker.
  • You can also mark the other corners of the pick with different measurements.
  • Alternatively, tape a coin to a pick 3 mm from the tip.
Step 4

Tape over any cracks

iPhone SE 2022 Lightning Connector Assembly Replacement — Tape over any cracks ⌕
Suction Handle
TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • If your iPhone has a cracked screen, keep further breakage contained and prevent bodily harm during your repair by taping over the glass.
  • Lay overlapping strips of clear packing tape over the iPhone's screen until the whole face is covered.
  • Wear safety glasses to protect your eyes from any glass shaken free during the repair.
  • If you can't get the suction cup to stick in the next few steps, fold a strong piece of tape (such as duct tape) into a handle and lift the screen with that instead.
  • If all else fails, you can superglue the suction cup to the screen.
Step 5

Anti-Clamp instructions

iPhone SE 2022 Lightning Connector Assembly Replacement — Anti-Clamp instructions ⌕
Suction Handle
TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide
View item
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • The next three steps demonstrate the Anti-Clamp, a tool we designed to make the opening procedure easier. If you aren't using the Anti-Clamp, skip down three steps for an alternate method.
  • For complete instructions on how to use the Anti-Clamp, check out this guide.
  • Pull the blue handle backwards to unlock the Anti-Clamp's arms.
  • Slide the arms over either the left or right edge of your iPhone.
  • Position the suction cups near the bottom edge of the iPhone just above the home button—one on the front, and one on the back.
  • Squeeze the cups together to apply suction to the desired area.
  • If you find that the surface of your iPhone is too slippery for the Anti-Clamp to hold onto, you can use tape to create a grippier surface.
Step 6

Repair step

iPhone SE 2022 Lightning Connector Assembly Replacement — repair step ⌕
Suction Handle
TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide
View item
  • Pull the blue handle forwards to lock the arms.
  • Turn the handle clockwise 360 degrees or until the cups start to stretch.
  • Make sure the suction cups remain aligned with each other. If they begin to slip out of alignment, loosen the suction cups slightly and realign the arms.
Step 7

Repair step

iPhone SE 2022 Lightning Connector Assembly Replacement — repair step ⌕
Heat Gun
TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide
View item
iOpener
TOOL USED ON THIS STEP iOpener Referenced by the iFixit guide
View item
  • Heat an iOpener and thread it through the arms of the Anti-Clamp.
  • You can also use a hair dryer, heat gun, or hot plate—but extreme heat can damage the display and/or internal battery, so proceed with care.
  • Fold the iOpener so it lays on the bottom edge of the iPhone.
  • Wait one minute to give the adhesive a chance to release and present an opening gap.
  • Insert an opening pick under the screen's plastic bezel, not the screen itself.
  • If the Anti-Clamp doesn't create a sufficient gap, apply more heat to the area and rotate the handle a quarter turn.
  • Don't crank more than a quarter turn at a time, and wait one minute between turns. Let the Anti-Clamp and time do the work for you.
  • Skip the next two steps.
Step 8

Heat the front panel adhesive

iPhone SE 2022 Lightning Connector Assembly Replacement — Heat the front panel adhesive ⌕
Heat Gun
TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide
View item
Suction Handle
TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide
View item
  • If you're using a suction handle, follow the next two steps to loosen the rear glass.
  • Prepare an iOpener and apply it to the screen for at least two minutes to loosen the adhesive underneath.
  • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.
Step 9

Screen information

iPhone SE 2022 Lightning Connector Assembly Replacement — Screen information ⌕
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • To avoid damaging your screen in the next step, note the following:
  • There's a plastic bezel on the underside of the screen. Your opening pick will go underneath this bezel.
  • There's a seam between the plastic bezel and the display panel. Don't insert your pick here or you'll damage the screen.
  • Sometimes the display panel separates from the bezel before you even get a chance to insert a pick. This may be unavoidable depending on the condition of the adhesive. In this case, you’ll most likely need to replace your entire screen.
Step 10

Insert an opening pick

iPhone SE 2022 Lightning Connector Assembly Replacement — Insert an opening pick ⌕
Suction Handle
TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide
View item
iOpener
TOOL USED ON THIS STEP iOpener Referenced by the iFixit guide
View item
  • Secure a suction handle to the lower half of the front panel, as close to the home button as possible.
  • Lift the front panel with the suction handle to create a small gap between the front panel and the frame.
  • If you have trouble creating a gap, apply more heat to the bottom half of the screen to further soften the adhesive. Follow the iOpener instructions to avoid overheating.
  • Insert an opening pick into the gap under the screen's plastic bezel.
Step 11

Slice the adhesive

iPhone SE 2022 Lightning Connector Assembly Replacement — Slice the adhesive ⌕
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • Slide the opening pick to the bottom right corner to slice the front panel adhesive.
  • Insert a second opening pick at the bottom edge of your phone.
  • Slide the opening pick to the bottom left corner to slice the adhesive.
  • Leave the opening picks in place to prevent the adhesive from resealing.
Step 12

Slice the adhesive

iPhone SE 2022 Lightning Connector Assembly Replacement — Slice the adhesive ⌕
iOpener
TOOL USED ON THIS STEP iOpener Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • If the adhesive becomes hard to cut, it has most likely cooled down. Use your iOpener for two to three minutes to reheat it.
  • Slide the bottom left opening pick along the left edge of your phone to slice the adhesive.
  • Stop near the top left corner of the display.
  • Do not try to pry the top edge of the display away from the rear case, as it is held in place by plastic clips that may break.
Step 13

Repair step

iPhone SE 2022 Lightning Connector Assembly Replacement — repair step ⌕
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • Slide the bottom right opening pick along the right edge of your phone to slice the adhesive.
  • Don't insert your pick more than 3 mm, as you may damage internal components.
  • Stop near the top right corner of the display.
Step 14

Lift the screen

iPhone SE 2022 Lightning Connector Assembly Replacement — Lift the screen ⌕
Suction Handle
TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • Remove the opening picks.
  • Gently pull up on the suction handle to lift up the bottom edge of the display.
  • Do not raise the display more than 15º or you'll risk straining or tearing the ribbon cables connecting the display.
  • Remove the suction handle.
Step 15

Slice the remaining adhesive

iPhone SE 2022 Lightning Connector Assembly Replacement — Slice the remaining adhesive ⌕
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • Slide an opening pick underneath the top left corner of the display.
  • Slide the opening pick around the top left corner and along the top edge of the phone to slice the remaining adhesive.
Step 16

Disengage the front panel clips

iPhone SE 2022 Lightning Connector Assembly Replacement — Disengage the front panel clips ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • Slide the display assembly slightly down in direction of the charging port to disengage the clips holding it to the rear case.
Step 17

Lift up the display

iPhone SE 2022 Lightning Connector Assembly Replacement — Lift up the display ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Open the phone by swinging the display up from the left side, like the back cover of a book.
  • Don't try to fully separate the display from the phone assembly yet, as several fragile ribbon cables still connect it to the logic board.
  • Lean the display against something to keep it propped up while you're working on the phone.
Step 18

Unfasten the lower display cable bracket screws

iPhone SE 2022 Lightning Connector Assembly Replacement — Unfasten the lower display cable bracket screws ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Remove the four Phillips screws securing the lower display cable bracket:
  • Two 1.2 mm-long screws
  • Two 2.8 mm-long screws
  • Throughout this guide, keep careful track of your screws so that each one goes back where it came from during reassembly. Installing a screw in the wrong place can cause permanent damage.
Step 19

Remove the lower display cable bracket

iPhone SE 2022 Lightning Connector Assembly Replacement — Remove the lower display cable bracket ⌕
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • Use a pair of tweezers to carefully remove the lower display cable bracket.
Step 20

Disconnect the battery

iPhone SE 2022 Lightning Connector Assembly Replacement — Disconnect the battery ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use the pointed end of a spudger to disconnect the battery by prying the connector straight up from its socket.
Step 21

Disconnect the display and digitizer cables

iPhone SE 2022 Lightning Connector Assembly Replacement — Disconnect the display and digitizer cables ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • The display and digitizer cables run on top of each other. To avoid cable damage always start by disconnecting the upper cable first and never try to disconnect both at the same time.
  • Use the pointed end of a spudger to disconnect the bottom two display cables by prying the connectors straight up from their sockets.
  • To re-attach press connectors like this, press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is even slightly misaligned, the connector can bend, causing permanent damage.
Step 22

Unfasten the front sensor assembly bracket screws

iPhone SE 2022 Lightning Connector Assembly Replacement — Unfasten the front sensor assembly bracket screws ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Use a Phillips screwdriver to remove the three 1.2 mm-long screws securing the front sensor assembly bracket.
Step 23

Remove the front sensor assembly bracket

iPhone SE 2022 Lightning Connector Assembly Replacement — Remove the front sensor assembly bracket ⌕
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use a pair of tweezers to carefully remove the front sensor assembly bracket.
Step 24

Disconnect the front sensor assembly cable

iPhone SE 2022 Lightning Connector Assembly Replacement — Disconnect the front sensor assembly cable ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use the pointed end of a spudger to disconnect the front sensor assembly by prying the connector straight up from its socket.
Step 25

Remove the display assembly

iPhone SE 2022 Lightning Connector Assembly Replacement — Remove the display assembly ⌕
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • Remove the display assembly.
  • During reassembly, follow this guide to apply adhesive and install your display assembly.
Step 26

Unfasten the Lightning connector bracket screws

iPhone SE 2022 Lightning Connector Assembly Replacement — Unfasten the Lightning connector bracket screws ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Unfasten the three screws securing the Lighting connector bracket:
  • One 1.2 mm-long Y000 screw
  • One 2.7 mm-long Phillips screw
  • One 2.9 mm-long Phillips screws
Step 27

Remove the Lightning connector bracket

iPhone SE 2022 Lightning Connector Assembly Replacement — Remove the Lightning connector bracket ⌕
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • Use a pair of tweezers to remove the Lightning connector bracket.
Step 28

Loosen the Wi-Fi diversity antenna flex cable

iPhone SE 2022 Lightning Connector Assembly Replacement — Loosen the Wi-Fi diversity antenna flex cable ⌕
iOpener
TOOL USED ON THIS STEP iOpener Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • Carefully slide an opening pick between the antenna flex cable and the top of the speaker.
  • This portion of the flex cable is lightly adhered to the speaker. If you're struggling to separate the cable from the speaker, apply a little heat from an iOpener or hair dryer to soften the adhesive. This will make it easier to separate the flex cable safely.
Step 29

Disconnect the Wi-Fi diversity antenna

iPhone SE 2022 Lightning Connector Assembly Replacement — Disconnect the Wi-Fi diversity antenna ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use the pointed end of a spudger to disconnect the Wi-Fi diversity antenna by prying its connector straight up from its socket.
  • The socket of this connector sits loosely between the speaker and the Taptic Engine and it's a bit fiddly to disconnect the cable. To make the disconnection easier, you can use an opening pick to hold down the connector socket during this procedure.
  • Reconnecting this cable can be tricky. Make it easier by using tweezers to hold the flex cable so the connector aligns with its socket. Then, gently press straight down on the connector with the flat of your spudger until it clicks into place.
Step 30

Repair step

iPhone SE 2022 Lightning Connector Assembly Replacement — repair step ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use the pointed end of a spudger to disconnect the Wi-Fi diversity antenna from the logic board by prying the connector straight up from its socket.
Step 31

Remove the Wi-Fi diversity antenna

iPhone SE 2022 Lightning Connector Assembly Replacement — Remove the Wi-Fi diversity antenna ⌕
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use a pair of tweezers to remove the Wi-Fi diversity antenna.
Step 32

Unfasten the Taptic Engine screws

iPhone SE 2022 Lightning Connector Assembly Replacement — Unfasten the Taptic Engine screws ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Remove the two screws securing the Taptic Engine:
  • One 2.1 mm Phillips screw
  • One 2.1 mm standoff screw
  • Standoff screws are best removed using a standoff screwdriver or bit.
  • In a pinch, a small flathead screwdriver will do the job—but use extra caution to ensure it doesn't slip and damage surrounding components.
Step 33

Remove the grounding bracket

iPhone SE 2022 Lightning Connector Assembly Replacement — Remove the grounding bracket ⌕
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use a pair of tweezers to remove the grounding bracket at the left edge of the Taptic Engine.
Step 34

Pry the antenna cable socket

iPhone SE 2022 Lightning Connector Assembly Replacement — Pry the antenna cable socket ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use the pointed end of your spudger to pry the antenna cable socket up and away from the Taptic Engine connector below.
Step 35

Disconnect the Taptic Engine

iPhone SE 2022 Lightning Connector Assembly Replacement — Disconnect the Taptic Engine ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use the pointed end of a spudger to disconnect the Taptic Engine by prying the connector straight up from its socket.
Step 36

Remove the Taptic Engine

iPhone SE 2022 Lightning Connector Assembly Replacement — Remove the Taptic Engine ⌕
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use a pair of tweezers to carefully remove the Taptic Engine.
Step 37

Unfasten the barometric vent screws

iPhone SE 2022 Lightning Connector Assembly Replacement — Unfasten the barometric vent screws ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Remove the two screws securing the barometric vent:
  • One 1.9 mm-long Phillips screw
  • One 1.7 mm-long Phillips screw
Step 38

Remove the barometric vent

iPhone SE 2022 Lightning Connector Assembly Replacement — Remove the barometric vent ⌕
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
iOpener
TOOL USED ON THIS STEP iOpener Referenced by the iFixit guide
View item
  • Use a pair of tweezers to remove the barometric vent.
  • The barometric vent is lightly adhered to the rear case. If you're struggling to separate the vent from the case, apply a little heat from an iOpener or hair dryer to soften the adhesive. This will make it easier to separate the barometric vent safely.
Step 39

Disconnect the rear camera

iPhone SE 2022 Lightning Connector Assembly Replacement — Disconnect the rear camera ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use the pointed end of a spudger to disconnect the rear camera by prying the connector straight up from its socket.
Step 40

Unfasten the rear camera bracket screws

iPhone SE 2022 Lightning Connector Assembly Replacement — Unfasten the rear camera bracket screws ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Remove the two screws securing the rear-facing camera bracket:
  • One 3.0 mm-long standoff screw
  • Standoff screws are best removed using a standoff screwdriver or bit.
  • In a pinch, a small flathead screwdriver will do the job—but use extra caution to ensure it doesn't slip and damage surrounding components.
  • One 3.1 mm-long Phillips screw
Step 41

Remove the rear camera bracket

iPhone SE 2022 Lightning Connector Assembly Replacement — Remove the rear camera bracket ⌕
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use a pair of tweezers to remove the rear camera bracket.
Step 42

Disconnect the flash

iPhone SE 2022 Lightning Connector Assembly Replacement — Disconnect the flash ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use the pointed end of a spudger to disconnect the flash by prying the connector straight up from its socket.
Step 43

Unfasten the upper cable bracket screws

iPhone SE 2022 Lightning Connector Assembly Replacement — Unfasten the upper cable bracket screws ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Remove the two screws securing the upper cable bracket:
  • One 2.8 mm-long Phillips screw
  • One 1.2 mm-long Phillips screw
Step 44

Remove the upper cable bracket

iPhone SE 2022 Lightning Connector Assembly Replacement — Remove the upper cable bracket ⌕
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • Use a pair of tweezers to remove the upper cable bracket.
Step 45

Disconnect the upper flex cable

iPhone SE 2022 Lightning Connector Assembly Replacement — Disconnect the upper flex cable ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use the pointed end of a spudger to disconnect the upper flex cable by prying the connector straight up from its socket.
Step 46

Unfasten the top left antenna component screws

iPhone SE 2022 Lightning Connector Assembly Replacement — Unfasten the top left antenna component screws ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Unfasten the three 1.2 mm-long Phillips screws securing the top left antenna component.
  • Don't try to remove the antenna component yet. There's a fourth screw securing it to the rear case.
Step 47

Repair step

iPhone SE 2022 Lightning Connector Assembly Replacement — repair step ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Unfasten the 1.4 mm-long Phillips screw securing the antenna component to the top edge of the rear case.
Step 48

Remove the top left antenna component

iPhone SE 2022 Lightning Connector Assembly Replacement — Remove the top left antenna component ⌕
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use a pair of tweezers to remove the top left antenna component.
Step 49

Unfasten the grounding bracket screws

iPhone SE 2022 Lightning Connector Assembly Replacement — Unfasten the grounding bracket screws ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Unfasten the two screws securing the top left grounding bracket:
  • One 1.5 mm-long Phillips screw
  • One 1.2 mm-long Phillips screw
Step 50

Remove the top left grounding bracket

iPhone SE 2022 Lightning Connector Assembly Replacement — Remove the top left grounding bracket ⌕
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use a pair of tweezers to remove the top left grounding bracket.
Step 51

Unfasten the logic board screws

iPhone SE 2022 Lightning Connector Assembly Replacement — Unfasten the logic board screws ⌕
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
  • Unfasten the four screws securing the logic board:
  • One 1.7 mm-long Phillips screw
  • One partially threaded 1.7 mm-long Phillips screw
  • This screw is covered by protective foam surrounding the rear camera connector. Use a pair of tweezers to peel just enough foam off to unfasten the screw.
  • One 2.5 mm-long standoff screw
  • One 2.2 mm-long standoff screw
Step 52

Pry up the logic board grounding bracket

iPhone SE 2022 Lightning Connector Assembly Replacement — Pry up the logic board grounding bracket ⌕
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • Use a pair of tweezers to carefully pry up the logic board grounding bracket in the top right corner of the rear case.
Step 53

Position the SIM card eject plunger

iPhone SE 2022 Lightning Connector Assembly Replacement — Position the SIM card eject plunger ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • Use the pointed end of a spudger to move the SIM card eject plunger out of the logic board's way by pushing it to the right edge of the rear case.
Step 54

Disconnect the Lightning port and the wireless charging coil cable

iPhone SE 2022 Lightning Connector Assembly Replacement — Disconnect the Lightning port and the wireless charging coil cable ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use the pointed end of a spudger to disconnect the Lightning port cable by prying the connector straight up from its socket.
  • Use the pointed end of a spudger to disconnect the wireless charging coil cable by prying the connector straight up from its socket.
Step 55

Pry up the logic board

iPhone SE 2022 Lightning Connector Assembly Replacement — Pry up the logic board ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use the flat end of a spudger to gently pry up the battery connector end of the logic board.
  • Be careful not to pry against any cables. If you feel resistance, check that all cables, connectors, and components are clear of the board.
Step 56

Remove the logic board

iPhone SE 2022 Lightning Connector Assembly Replacement — Remove the logic board ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Grasping it by the edges, lift the logic board near the battery connector and remove it.
  • Make sure that none of the surrounding cables are tangled with the logic board or blocking its way.
Step 57

Unfasten the loudspeaker screws

iPhone SE 2022 Lightning Connector Assembly Replacement — Unfasten the loudspeaker screws ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Unfasten the two screws securing the loudspeaker:
  • One 1.4 mm-long Phillips screw
  • One 2.1 mm-long Phillips screw
Step 58

Remove the loudspeaker

iPhone SE 2022 Lightning Connector Assembly Replacement — Remove the loudspeaker ⌕
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use a pair of tweezers to remove the loudspeaker.
Step 59

Unfasten the Lightning connector assembly screws

iPhone SE 2022 Lightning Connector Assembly Replacement — Unfasten the Lightning connector assembly screws ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Unfasten the five screws securing the lighting connector to the rear case:
  • One 1.3 mm-long Phillips screw
  • Two 2.3 mm-long Phillips screws
  • Two 1.4 mm-long Phillips screws
Step 60

Free the microphones

iPhone SE 2022 Lightning Connector Assembly Replacement — Free the microphones ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • Use the pointed end of a spudger to gently pry the two microphones on the left and right of the Lightning connector free from the adhesive securing them in place.
  • Don't try to completely remove the microphones; just separate the adhesive as shown.
Step 61

Loosen the charging port assembly adhesive

iPhone SE 2022 Lightning Connector Assembly Replacement — Loosen the charging port assembly adhesive ⌕
iOpener
TOOL USED ON THIS STEP iOpener Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • Apply a heated iOpener to the bottom of the rear case to loosen the charging port assembly adhesive, angling it as shown.
Step 62

Separate the Lightning connector assembly cable

iPhone SE 2022 Lightning Connector Assembly Replacement — Separate the Lightning connector assembly cable ⌕
iOpener
TOOL USED ON THIS STEP iOpener Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • Slide an opening pick underneath the top portion of the Lightning connector assembly flex cable, and begin separating the cable from the rear case.
  • Part of the wireless charging coil lies directly underneath this portion of the Lightning connector flex cable. Aggressive prying may damage the coil.
  • If needed, use your hair dryer or iOpener repeatedly to re-heat the area behind the Lightning connector assembly flex cable in order to further soften its adhesive.
  • Continue separating the upper portion of the flex cable, being careful not to damage any other components along the way.
  • Keep the battery connector gently folded out of the way to avoid damaging it.
  • Be very careful not to damage the battery itself. A punctured battery can leak dangerous chemicals and/or catch fire.
  • Stop sliding the pick once it passes the lower edge of the battery.
Step 63

Repair step

iPhone SE 2022 Lightning Connector Assembly Replacement — repair step ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Starting at the corner of the phone, slide the pick underneath the cable towards the Lightning connector.
  • Stop sliding the pick when it reaches the Lightning connector.
Step 64

Repair step

iPhone SE 2022 Lightning Connector Assembly Replacement — repair step ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Gently pull the Lightning connector out of its recess in the rear case.
  • Don't try to remove the lightning connector assembly all the way yet. It is still partly adhered to the rear case.
Step 65

Repair step

iPhone SE 2022 Lightning Connector Assembly Replacement — repair step ⌕
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • Slide an opening pick below the Lightning connector to further separate the assembly from the rear case.
  • Continue to slide the pick until the Lightning connector assembly is no longer adhered to the bottom of the rear case.
  • Don't try to remove the lightning connector assembly all the way yet. A last bit is still adhered to the left edge of the rear case.
Step 66

Repair step

iPhone SE 2022 Lightning Connector Assembly Replacement — repair step ⌕
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • Slide an opening pick between the left edge of the rear case and the remaining adhered section of the Lightning assembly.
Step 67

Remove the Lightning connector assembly

iPhone SE 2022 Lightning Connector Assembly Replacement — Remove the Lightning connector assembly ⌕
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
  • Remove the Lightning connector assembly.
  • Before installing or replacing the Lightning connector assembly:
  • Remove any remaining adhesive, and clean the glued areas with isopropyl alcohol and a lint-free cloth.
  • Before removing the adhesive backing on a new assembly, make sure the Lightning connector assembly is correctly positioned by aligning the hole in the flex cable with the screw post. If the cable is misaligned, you won't be able to reconnect it to the logic board.
Step 68

Transferring and replacing remaining components

iPhone SE 2022 Lightning Connector Assembly Replacement — Transferring and replacing remaining components ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • A rubber gasket on the bottom of the Lightning connector protects your iPhone from liquid and dust intrusion. If you are installing a new Lightning connector assembly, you may need to carefully remove and transfer the gasket to the new part.
  • The small adhesive patch on the bottom of each microphone also protects your iPhone from liquid and dust intrusion. For best results, replace the two adhesive patches before installing your Lightning connector assembly.
  • Check if your new part comes with an antenna converter cable. If it doesn't, use the pointed end of your spudger to pry up and transfer the cable from your old Lightning assembly to the new one.