iPhone 15 Pro Front Camera Assembly Replacement

Step 1

Prepare your iPhone for disassembly

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

• Let your phone's battery drain below 25% before starting this repair—a charged lithium‑ion battery may catch fire if damaged.
• Unplug all cables from your phone.
• Hold the power and either volume button and slide to power off your phone.

Step 2

Tape over any cracks

⌕

TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide

View item

• If your screen or back glass is cracked, lay overlapping strips of packing tape over the glass to protect yourself and make disassembly easier.
• Make sure there's a smooth area near the bottom edge that's big enough for a suction cup to stick to.

Step 3

Mark your opening picks

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• If inserted too far, an opening pick can damage your device. Follow this step to mark your pick and prevent damage.
• Measure 3 mm from the tip and mark the opening pick with a permanent marker.
• You can also mark the other corners of the pick with different measurements.
• Alternatively, tape a coin to a pick 3 mm from the tip.

Step 4

Remove the pentalobe screws

⌕

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide

View item

• Use a P2 pentalobe screwdriver to remove the two 7 mm‑long screws on either side of the charging port.

Step 5

Heat the bottom edge

⌕

TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide

View item

• Use a hair dryer or heat gun to heat the bottom edge of the screen until it's hot to the touch.
• Be careful not to heat the phone hotter than this—the battery is susceptible to heat damage.

Step 6

Insert an opening pick

⌕

TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

• Apply a suction handle to the bottom edge of the screen.
• Pull up on the handle with a strong, steady force to create a gap between the screen and the frame.
• Insert the tip of an opening pick into the gap.

Step 7

Screen information

⌕

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• As you slice the adhesive securing the screen in the next steps, be careful of the following areas:
• There are two delicate cables connecting the screen to the phone: one just above the action button, and the other near the middle of the left edge.
• There are multiple spring contacts around the perimeter of the phone. Be extra careful not to insert your pick deeper than suggested in these locations to avoid bending the contacts.

Step 8

Separate the bottom edge adhesive

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

• Don't insert your opening pick deeper than 3 mm along the bottom edge.
• Slide your pick back and forth along the bottom edge to separate the adhesive.
• Leave your pick inserted in the bottom right corner to prevent the adhesive from re-sealing.

Step 9

Heat the right edge

⌕

• Heat the right edge of the screen until it's hot to the touch.

Step 10

Position the opening pick

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• Don't insert your pick deeper than 5 mm along the right edge.
• Slide your pick around the bottom right corner of the screen and toward the power button until you feel a hard stop at a clip securing the screen.
• Rotate your pick so the flat edge is under the screen.

Step 11

Release the right clip

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• Twist the pick to increase the gap between the screen and the frame until the right clip releases.
• Insert a second opening pick to the right of the first pick.

Step 12

Separate the right edge adhesive

⌕

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

• Slide the first pick back to the bottom right corner of the screen.
• Slide the second pick to the top right corner of the screen to separate the adhesive.
• Leave these picks inserted to prevent the adhesive from resealing.

Step 13

Heat the top edge

⌕

• Heat the top edge of the screen until it's hot to the touch.

Step 14

Separate the top edge adhesive

⌕

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

• Don't insert your pick deeper than 3 mm along the top edge.
• Slide your pick around the top right corner and along the top edge to release the two clips and adhesive securing it.

Step 15

Heat the left edge

⌕

• Heat the left edge of the screen until it's hot to the touch.

Step 16

Separate the left edge adhesive

⌕

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• Don't insert your pick deeper than 2 mm along the left edge to avoid the two cables connecting the screen to the phone.
• Rotate your pick around the top left corner of the screen.
• Slide your pick to the bottom left corner of the screen to separate the adhesive.

Step 17

Prop up the screen

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

• Place a small box or stack of books to the left of your phone so you can prop up the screen while disconnecting its cables.
• Swing up the right edge of the screen like the front cover of a book.
• If the screen feels stuck, go back around the perimeter with an opening pick to separate any remaining adhesive.
• Prop up the screen so you can access its cables without straining them.

Step 18

Unfasten the logic board cover

⌕

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide

View item

• Use a Y000 screwdriver to remove the six screws securing the logic board cover:
• Four 1.6 mm‑long screws
• Two 1.3 mm‑long screws

Step 19

Remove the logic board cover

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

• Rotate the bottom of the logic board cover counterclockwise and slide the top left corner out from under the ambient light sensor cable to remove it.
• During reassembly, make sure the top left corner of the cover goes under the ambient light sensor cable.

Step 20

Disconnect the battery

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• Use the tip of an opening pick to pry up and disconnect the battery press connector from the bottom right corner of the logic board.
• To reconnect a press connector, align it over its socket and gently press down on one side until it clicks into place, then press down on the other side. Make sure it sits flat, as the insulating rubber around the sockets might prevent it from connecting fully.

Step 21

Disconnect the screen

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• Use the tip of an opening pick to pry up and disconnect the screen cable from the center of the logic board.

Step 22

Disconnect the ambient light sensor

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• Gently slide the tip of an opening pick under the ambient light sensor cable near the top left corner of the logic board.
• Lift the cable to disconnect it.

Step 23

Remove the screen

⌕

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

• Remove the screen.
• During reassembly, follow this guide to apply new adhesive and install your screen.
• Be careful not to damage any of the spring contacts as you clean the frame.

Step 24

Disconnect the rear cameras

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• Use the tip of an opening pick to pry up and disconnect the three rear camera press connectors from the top right of the logic board.
• The third connector is hidden beneath the top one—lift the top cable slightly to reveal the third connector.

Step 25

Unfasten the rear cameras

⌕

TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

• Use a Phillips #000 screwdriver to remove the three screws securing the rear cameras:
• One 3.8 mm‑long screw
• One 3.2 mm‑long screw
• One 2.8 mm‑long screw

Step 26

Remove the rear cameras

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

• Be careful not to touch or smudge the camera lenses during this step.
• Insert the point of a spudger between the top right corner of the rear cameras and frame.
• Pry up until you can grab the rear cameras with your fingers.
• Remove the rear cameras.

Step 27

Unfasten the earpiece speaker

⌕

TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

• Use a Phillips #000 screwdriver to remove the 2 mm‑long screw securing the top of the earpiece speaker.
• Use a standoff screwdriver to remove the remaining screw securing the bottom left corner of the earpiece speaker.
• If you don't have a standoff screwdriver, you can use a thin flathead one instead. Apply constant, downward pressure to avoid damaging the shallow notches in the screw head.

Step 28

Remove the earpiece speaker

⌕

• Remove the earpiece speaker.

Step 29

Move the microphone cable

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• The microphone cable covers the front sensors press connector.
• Use the tip of an opening pick to disconnect the microphone press connector from the top left corner of the logic board.
• Lift the cable out of the way so you can access the two press connectors on the logic board's top edge.

Step 30

Disconnect the front camera assembly

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• Use the tip of an opening pick to pry up and disconnect the front sensors and front camera press connectors from the top edge of the logic board.

Step 31

Remove the front camera assembly

⌕

• Remove the front camera assembly.
• Be careful not to touch or smudge the camera or sensor lenses.

Step 32

Disassembly complete

⌕

• Congratulations on completing disassembly! The remaining steps show how to reassemble the iPhone.

Step 33

Install the front camera assembly

⌕

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

• Be careful not to touch or smudge the front camera or sensor lenses.
• If the replacement cameras include a plastic liner to protect the lenses, keep it in place until just before you reinstall the screen.
• Use tweezers to align the front camera assembly with its recess in the frame and set it into place.

Step 34

Connect the front camera assembly

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

• Use your finger or the flat end of a spudger to connect the front camera assembly's press connectors to their sockets on the top edge of the logic board.

Step 35

Connect the microphone

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

• Use your finger to connect the microphone press connector to its socket on the top left corner of the logic board.

Step 36

Install the earpiece speaker

⌕

• Align the gasket on the top right corner of the earpiece speaker with its recess in the frame.
• Press the gasket into its recess, then lower the earpiece speaker into place.

Step 37

Install the earpiece speaker screws

⌕

TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

• Use a Phillips #000 screwdriver to install the 2 mm‑long screw securing the top of the earpiece speaker.
• Use a standoff screwdriver to install the remaining screw securing the bottom left corner of the earpiece speaker.
• If you don't have a standoff screwdriver, you can use a thin flathead one instead. Apply constant, downward pressure to avoid damaging the shallow notches in the screw head.

Step 38

Install the rear camera assembly

⌕

• Be careful not to touch or smudge the camera lenses.
• Align the rear camera assembly with its recess in the frame and set it into place.

Step 39

Install the rear camera assembly screws

⌕

TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

• Use a Phillips #000 screwdriver to install the three screws securing the rear cameras:
• One 3.8 mm‑long screw
• One 3.2 mm‑long screw
• One 2.8 mm‑long screw

Step 40

Connect the rear cameras

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

• Use the flat end of a spudger to connect the three rear camera press connectors—starting with the black one—to their respective sockets on the logic board.

Step 41

Remove the screen adhesive

⌕

TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• The adhesive remaining on the phone is difficult to remove and leaves residue. If you have trouble removing the adhesive, apply some heat using a hair dryer or heat gun.
• Use a spudger to push the screen adhesive up until you can grab it with a pair of tweezers.
• Use a pair of tweezers, or your fingers, to remove the adhesive around the entire perimeter of the iPhone.

Step 42

Repair step

⌕

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

• Any unevenness will compromise the iPhone's seal. Clean the frame thoroughly.
• Apply a few drops of high-concentration (greater than 90%) isopropyl alcohol to a cotton swab or lint-free cloth.
• Wipe along the perimeter of the frame to clean the adhesive residue.
• Wait a few minutes before proceeding to make sure any excess alcohol has evaporated.

Step 43

Orient the adhesive

⌕

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

• Lay the adhesive next to the phone and use features like cutouts for spring contacts and the front‑facing camera to orient it correctly.

Step 44

Apply the adhesive

⌕

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

• Once the adhesive is pressed into place, you can't reposition it—you'll have to remove it and start over with new adhesive.
• Use the pull tab to begin peeling the back liner off of the adhesive starting from the bottom, but don't remove it all the way.
• While holding the back liner out of the way, carefully align the exposed edge of the adhesive to the bottom edge of the iPhone's frame.
• When the adhesive is aligned, set it down along the bottom edge.

Step 45

Repair step

⌕

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

• Continue peeling the back liner off of the adhesive while setting the adhesive into place along the edges of the iPhone's frame.
• If you correctly aligned the lower edge of the adhesive, the side and top edges will fall perfectly into place. If the adhesive is misaligned, remove it and start over with new adhesive.
• If you don't have another one handy, it's okay to put your iPhone back together without adhesive, but keep in mind that it won't be water resistant until you install new adhesive.

Step 46

Press the adhesive into place

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

• Use the flat end of a spudger to press the adhesive into place all around the iPhone.
• Be careful not to press on the camera, spring contacts, or other internal components.

Step 47

Remove the top liner

⌕

• Lift the pull tab in the top‑right corner of the frame to peel off the top liner and remove it.
• Your pull tab may be in a different location. Make sure you're pulling the full-size top liner, not the thin liners along the edges.

Step 48

Adhesive information

⌕

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

• Once the top liner is removed, there should be three narrow liners on top of the adhesive with pull tabs near the bottom edge.
• Your pull tabs may be in different positions.
• If you don't see these pull tabs, you may have accidentally removed the thin liners in the previous step. Be careful not to touch anything to the exposed adhesive.

Step 49

Prop up the screen

⌕

• Prop the screen up along the left edge of the iPhone frame, using a box or similar sturdy object to support the screen.

Step 50

Connect the screen and ambient light sensor

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

• Use your finger or the flat end of a spudger to connect the screen and ambient light sensor press connectors.

Step 51

Connect the battery

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

• Use your finger or the flat end of a spudger to connect the battery press connector.

Step 52

Install the logic board cover

⌕

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide

View item

• Slide the top left corner of the logic board cover under the ambient light sensor cable and set it into place, aligned with its screw holes.

Step 53

Fasten the logic board cover

⌕

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide

View item

• Use a Y000 screwdriver to install the six screws securing the logic board cover:
• Four 1.6 mm‑long screws
• Two 1.3 mm‑long screws

Step 54

Remove the final adhesive liners

⌕

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

• Once you remove the liners in this step, the adhesive will be fully exposed. Make sure nothing accidentally sticks to it.
• Use tweezers to remove the two narrow liners covering the adhesive along the right, top, and bottom edges of the frame.

Step 55

Repair step

⌕

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

• Without letting the screen touch the adhesive, hold the screen over the phone so you can access the final liner along the left edge of the frame.
• Use a pair of tweezers or your fingers to remove the final liner along the left edge of the frame.

Step 56

Place the screen

⌕

• Align the screen over the frame, then lower it into place.

Step 57

Press the screen

⌕

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

• Firmly press along the edges of the screen to engage the clips and compress the adhesive.

Step 58

Install the pentalobe screws

⌕

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide

View item

• Use a P2 pentalobe screwdriver to install the two 7 mm‑long screws on either side of the charging port.

Step 59

Heat the screen

⌕

TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide

View item

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

• To help the adhesive bond, apply heat to the edges of the screen using a hair dryer or heat gun until it's hot to the touch.
• If you have screen vise clamps, use them to strengthen the bond of the new adhesive. If not, keep reading for more ways to secure the screen.

Step 60

Press the back glass

⌕

• To evenly compress the iPhone and strengthen the bond of the screen to the frame, you need to account for the camera bump.
• If you have the iPhone's original box, take the lid and place it on a flat surface.
• If you don't have the original box, skip this step for an alternate method.
• Place the iPhone screen-side-up in the lid of the box with the camera bump in its recess.
• Find something close to the size of the iPhone, but taller than the sides of the box. Stack it on top of the iPhone, followed by a few heavy objects.
• Leave the objects in place for at least thirty minutes, ideally overnight.

Step 61

Repair step

⌕

• If you don't have the iPhone's original box, follow the these two steps for another method to evenly compress the screen.
• Place the iPhone screen-side-down on a soft, flat surface.
• Apply tape to the back glass to protect its finish.
• Place three layers of coins or similarly thick objects on the tape along the edges of the back glass.
• Evenly distribute the coins and make sure they are at least as thick as the camera bump.

Step 62

Repair step

⌕

• Stack multiple books or other heavy objects on your iPhone.
• The coins may leave an impression on the bottom object, so don't use anything valuable.
• Leave the objects in place for at least thirty minutes, ideally overnight.