Home/ Repair guides/ iPhone 15 Plus Earpiece Speaker Replacement

Official iFixit API visual reference

iPhone 15 Plus Earpiece Speaker Replacement

Use this guide to replace the earpiece speaker...

Apple iPhone 15 Plus Moderate 1 - 2 hours Guide 166855

Licensed iFixit integration

This attributed iFixit guide is displayed through Fixonic's recorded commercial API permission. iFixit remains the independent source and author of the procedure.

Guide overview

Before you begin

Use this guide to replace the earpiece speaker in your iPhone 15 Plus. If the sound coming through your iPhone, especially during phone calls, sounds like static or crackling, your earpiece speaker may need to be replaced. You'll need replacement back glass adhesive to complete this repair.

Step 1

Prepare your phone for disassembly

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

Allow your phone's battery to drain below 25%, as a charged lithium-ion battery is a potential safety hazard.
Unplug any cables from your phone.
Hold the power and either volume buttons and slide to power off your phone.

Step 2

Tape over any cracks

⌕

TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide

View item

If your screen or back glass is badly cracked, lay overlapping strips of packing tape over the glass to protect yourself and make disassembly easier.
Make sure there's a smooth area near the bottom edge that's big enough for a suction cup to stick to.

Step 3

Mark your opening picks

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

If inserted too far, an opening pick can damage your device. Follow this step to mark your pick and prevent damage.
Measure 3 mm from the tip and mark the opening pick with a permanent marker.
You can also mark the other corners of the pick with different measurements.
Alternatively, tape a coin to a pick 3 mm from the tip.

Step 4

Remove the pentalobe screws

⌕

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide

View item

Use a P2 pentalobe driver to remove the two 7.7 mm-long screws on either side of the charging port.

Step 5

Heat the bottom edge

⌕

TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide

View item

Use a hair dryer or heat gun to heat the bottom edge of the back glass until it's hot to the touch.
Be careful not to heat the phone hotter than this—the battery is susceptible to heat damage.

Step 6

Insert an opening pick

⌕

TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

Apply a suction handle to the bottom edge of the back glass.
Pull up on the handle with a strong, steady force to create a gap between the back glass and the frame.
Insert the tip of an opening pick into the gap.

Step 7

Back glass information

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

As you slice the adhesive securing the back glass in the next steps, be careful of the following areas:
There's a delicate cable connecting the back glass to the phone, right next to the volume up button. Don't insert your pick here to avoid slicing the cable.
There are multiple spring contacts around the perimeter of the phone. Be extra careful not to insert your pick deeper than suggested in each step to avoid bending these contacts.

Step 8

Separate the bottom edge adhesive

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Don't insert your opening pick deeper than 5 mm along the bottom edge.
Slide your pick back and forth along the bottom edge to separate the adhesive.
Leave your pick inserted in the bottom right corner to prevent the adhesive from re-sealing.

Step 9

Heat the right edge

⌕

Heat the right edge of the back glass until it's hot to the touch.

Step 10

Separate the bottom right corner adhesive

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

Don't insert your pick deeper than 7 mm along the right edge.
Rotate your pick around the bottom right corner and slide it halfway up the right edge or until you feel a hard stop at a clip securing the back glass.
Don't slice near the volume buttons to avoid damaging the wireless charging cable.
Leave this pick inserted to prevent the adhesive from resealing.

Step 11

Heat the left edge

⌕

Heat the left edge of the back glass until it's hot to the touch.

Step 12

Separate the left edge adhesive

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Don't insert your pick deeper than 5 mm along the left edge.
Insert a second opening pick at the bottom edge.
Rotate the second pick around the bottom left corner.
Slide this pick up to the top left corner to separate the adhesive.
Leave this pick inserted to prevent the adhesive from resealing.

Step 13

Heat the top edge

⌕

Heat the top edge of the back glass until it's hot to the touch.

Step 14

Separate the top edge adhesive

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Don't insert your pick deeper than 3 mm along the top edge.
Rotate your second opening pick around the top left corner and slide it to the top right corner to separate the adhesive.
You might hear and feel clicks as the top two clips release.
Leave this pick in place to prevent the adhesive from resealing.

Step 15

Heat the top right corner

⌕

Heat the top right corner of the back glass until it's hot to the touch.

Step 16

Separate the top right corner adhesive

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Don't insert your pick deeper than 4 mm along the right edge.
Rotate the second opening pick around the top right corner and slide it to the volume up button to separate the adhesive.

Step 17

Swing open the back glass

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

Gently swing open the back glass to the right of the phone.
If the back glass feels stuck, go back around the perimeter to check for missed sections of adhesive or stuck clips.
Rest the back glass against a raised surface so it doesn't strain the cable.

Step 18

Unfasten the lower connector cover

⌕

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide

View item

Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.
Use a tri-point Y000 driver to remove the two 1.3 mm-long screws securing the lower connector cover.

Step 19

Remove the lower connector cover

⌕

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Use tweezers to slide the cover toward the top of the phone to unlatch it from the logic board.
Remove the cover.

Step 20

Repair step

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Hold the back glass upright with one hand and rotate the bottom edge to the left to reveal the battery press connector just below the volume buttons.
Use the tip of an opening pick to pry up and disconnect the battery press connector from the logic board.
A plus and minus sign is printed on the head of this connector.
To reconnect a press connector, align it over its socket and gently press down on one side until it clicks into place, then press down on the other side. Make sure it sits flat, as the insulating rubber around the sockets might prevent it from connecting fully.

Step 21

Remove the upper connector cover

⌕

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide

View item

Use your tri-point Y000 driver to remove the two 1.3 mm‑long screws securing the upper connector cover.
Remove the cover.

Step 22

Disconnect the front camera assembly

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Use the tip of an opening pick to pry up and disconnect the antenna, front sensors, and front camera press connectors (three connectors in total).

Step 23

Remove the front camera and sensors

⌕

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

Use tweezers or your fingers to pull the front camera and sensors out of their recess in the frame and remove them.

Step 24

Disconnect the earpiece speaker

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Use the tip of an opening pick to pry up and disconnect the earpiece speaker press connector.

Step 25

Unfasten the earpiece speaker

⌕

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide

View item

Use a Phillips #000 driver to remove the seven screws securing the earpiece speaker:
Five 1.6 mm‑long screws
Two 1.3 mm‑long screws

Step 26

Remove the earpiece speaker

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

Insert the flat end of a spudger between the top left edge of the earpiece speaker and pry up until you can grab it with your fingers.
Remove the earpiece speaker.

Step 27

Remove the antenna

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Your earpiece speaker has an adhered antenna that must be transferred to your new speaker.
Insert your opening pick between the antenna and the earpiece speaker.
Slide the pick under the antenna and pry up to separate the adhesive securing it.
Remove the antenna

Step 28

Reassembly information

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

During reassembly, follow these steps to reinstall the antenna:
Remove any leftover adhesive from the earpiece speaker and antenna.
If the existing adhesive is still sticky, you can reuse it instead of applying new tape.
Before sticking the antenna to the earpiece speaker, fasten the earpiece speaker to the frame and install the front camera and sensors. Connect all three press connectors.
Apply a small piece of thin, double-sided tape, such as Tesa tape, to the antenna.
Finally, connect the antenna press connector, then stick it onto the earpiece speaker.