Home/ Repair guides/ PlayStation 5 Slim Fan Replacement

Official iFixit API visual reference

PlayStation 5 Slim Fan Replacement

Follow this guide to replace a broken or faulty...

Sony PlayStation 5 Slim Moderate 10 - 20 minutes Guide 167652

Licensed iFixit integration

This attributed iFixit guide is displayed through Fixonic's recorded commercial API permission. iFixit remains the independent source and author of the procedure.

Guide overview

Before you begin

Follow this guide to replace a broken or faulty fan in your PlayStation 5 Slim. If your fan isn't spinning, is spinning very slowly, or is making very loud noises, you may need to replace it. You can also use this guide to clean out a dusty or dirty fan. Before purchasing a replacement fan, it's a good idea to remove your current fan and clean off any dust, dirt, hair, or grime that may have accumulated—it's possible this alone is the problem. If the fan still shows signs of being faulty after cleaning, then consider purchasing a replacement.

Step 1

Prepare your PlayStation for disassembly

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Before starting your repair:
Shut down your console and unplug all cables and accessories.
Remove any stands supporting your device and lay it down.

Step 2

Lay your PlayStation down

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Lay your PlayStation on its side so the right side covers are facing up.

Step 3

Remove the fan and SSD cover

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

The cover is secured with hooks along the back edge and clips along the front edge.
Firmly pull up the front edge of the smaller, upper cover to release the clips.
You'll hear distinct "pops" as the clips disengage.
Remove the cover.
To reinstall the cover, place the hooks into their cutouts along the rear edge and firmly press the front edge of the cover into place to re‑engage the two clips.

Step 4

Remove the fan cables cover

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

A piece of plastic covers the fan cables connector.
Use your fingers to remove the plastic cover.
During reassembly, press the piece of plastic back into place to secure it with the leftover adhesive. If it isn't sticking, use strips of double-sided tape to secure it.

Step 5

Free the fan cables

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Gently pull the fan cables out from under their plastic clip on the frame.

Step 6

Disconnect the fan

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Firmly grip the fan cables' white connector head and pull it straight up and out of its socket.
If you're having trouble, grip the cables just above the connector head, and gently pull.
During reassembly, align the connector over its socket and push down on the edges with the flat end of a spudger until it slides fully into its socket.

Step 7

Remove the fan screws

⌕

TOOL USED ON THIS STEP T8 Torx Security Bit Screwdriver Referenced by the iFixit guide

View item

Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.
Use a T8 Torx Security screwdriver to remove the four screws securing the fan:
One 31.2 mm‑long screw
Two 21.3 mm‑long screws
One 11.6 mm‑long screw

Step 8

Remove the fan

⌕

TOOL USED ON THIS STEP Compressed Air Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Use your fingers to grab the fan by its vents and lift it straight up to remove it.
If you're using this guide to clean your fan, use compressed air and a clean cloth to remove any dust or dirt.
During reassembly, insert the fan so its cables are near their connector.