Fairphone 5 Main Camera Replacement

Step 1

Prepare your phone for disassembly

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• Unplug all cables and power down your phone.
• Press the power and volume up buttons at the same time to bring up the shutdown menu.

Step 2

Pry up the back cover

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• Insert your fingernail, or a pry tool like a spudger, under the notch at the bottom right of the back cover.
• Pry up the back cover to release the bottom right corner clips.

Step 3

Remove the back cover

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• Grip the bottom right corner of the back cover with one hand and brace the phone frame with the other.
• Lift the back cover away from the phone to release the clips around its perimeter.
• Remove the back cover.
• During reassembly, align the back cover over the phone and press along the perimeter until all clips snap back into place.

Step 4

Remove the battery

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• Use your fingernail, or a pry tool like a spudger, to lift the battery by its tab along the bottom edge.
• Remove the battery.
• During reassembly, slide the top edge of the battery into its recess in the frame before pressing the battery into place.

Step 5

Unfasten the connector cover

⌕

TOOL USED ON THIS STEP Phillips #00 Screwdriver Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• Use a Phillips driver to remove the 3.9 mm-long screw securing the top unit connector cover at the bottom left corner.
• The connector cover is labeled with a "1" and a triangle pointing downward.

Step 6

Pry up the connector cover

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• Insert your fingernail, or a pry tool like a spudger, under the notch at the left edge of the connector cover.
• Pry up the cover to separate it from the top unit.
• The cover is connected to the top unit by a plastic cord. Don't try to completely remove it from the top unit.

Step 7

Disconnect the top unit

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• While holding the cover out of the way, use a spudger to pry up and disconnect the top unit press connector.
• To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Don't press down in the middle. If the connector is misaligned, the pins can bend and cause permanent damage.

Step 8

Unfasten the top unit

⌕

TOOL USED ON THIS STEP Phillips #00 Screwdriver Referenced by the iFixit guide

View item

• Use a Phillips driver to remove the six 4.9 mm‑long screws securing the top unit.

Step 9

Remove the top unit

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Phillips #00 Screwdriver Referenced by the iFixit guide

View item

• Insert the flat end of a spudger under the screw hole along the bottom edge of the top unit.
• Pry up to release the clips securing the top unit to the phone frame.
• During reassembly, insert the top edge of the top unit at a downward angle into the frame before pressing it down and re-engaging the clips.

Step 10

Disconnect the main camera

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• Insert the tip of a spudger under the right edge of the main camera press connector.
• Pry up to disconnect the main camera.

Step 11

Remove the main camera

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• Use a spudger, or your fingers, to lift the main camera out of its slot in the frame.
• Be careful to not touch the lens on the other camera during this procedure.
• Remove the main camera.