iPhone 16 Plus Loudspeaker Removal

Step 1

Heat the bottom edge

⌕

• Apply a heated iOpener to the bottom edge of the back glass for two minutes.
• Alternatively, you can use a hair dryer or heat gun to heat the bottom edge of the back glass until it's hot to the touch.
• Be careful not to heat the phone hotter than this—the battery is susceptible to heat damage.

Step 2

Insert an opening pick

⌕

• Apply a suction handle to the bottom edge of the back glass, above the USB-C port.
• Pull up on the handle with a strong, steady force to create a gap between the back glass and the frame.
• Insert the tip of an opening pick into the gap.

Step 3

Back glass information

⌕

• As you slice the adhesive securing the back glass in the next steps, be careful of the following areas:
• There's a delicate cable connecting the back glass to the phone, right next to the volume up button. Don't insert your pick here to avoid slicing the cable.
• There are multiple spring contacts around the perimeter of the phone. Be extra careful not to insert your pick deeper than suggested in each step to avoid bending these contacts.

Step 4

Separate the bottom edge adhesive

⌕

• Don't insert your pick deeper than 5 mm on the bottom edge to avoid damaging the spring contacts.
• Slide your pick back and forth along the bottom edge to separate the adhesive.
• Leave your pick inserted in the bottom right corner to prevent the adhesive from resealing.

Step 5

Heat the right edge

⌕

• Apply a heated iOpener to the right edge of the back glass for two minutes.
• When using a hair dryer or heat gun, heat the back glass until it's hot to the touch.

Step 6

Separate the bottom right corner adhesive

⌕

• Don't insert your pick deeper than 5 mm along the right edge to avoid damaging the spring contacts and ribbon cable.
• Slide your pick around the bottom right corner and slide it halfway up the right edge, or until you feel a hard stop at a clip securing the back glass.
• Don't slice near the volume buttons to avoid damaging the wireless charging/flash cable.
• Leave this pick inserted to prevent the adhesive from resealing.

Step 7

Heat the left edge

⌕

• Apply a heated iOpener to the left edge of the back glass for two minutes.
• When using a hair dryer or heat gun, heat until it's hot to the touch.

Step 8

Separate the left edge adhesive

⌕

• Don't insert your pick deeper than 5 mm along the left edge to avoid damaging the spring contact.
• Insert a second opening pick at the bottom edge.
• Slide the second pick around the bottom left corner and along the left edge of the screen to separate the adhesive and release the metal clips.
• You'll hear and feel the metal clips release as you pass them.
• Leave this pick inserted at the top left corner to prevent the adhesive from resealing.

Step 9

Heat the top edge

⌕

• Apply a heated iOpener to the top edge of the back glass, angled to include the volume buttons, for two minutes.
• When using a hair dryer or heat gun, heat until it's hot to the touch.

Step 10

Separate the top edge adhesive

⌕

• Don't insert your pick deeper than 3 mm along the top edge to avoid damaging the spring contacts.
• Slide your opening pick across the top edge and around the top right corner to the volume up button to separate the adhesive.
• You should hear and feel clicks as the top two clips release.

Step 11

Swing open the back glass

⌕

• Don't try to fully remove the back glass just yet—it's still attached with a delicate ribbon cable. Follow the next few steps to remove it safely.
• If the back glass doesn't swing open easily, don't force it—go back around the perimeter with your pick to check for missed sections of adhesive or stuck clips.
• You may need to lift the back glass up slightly before swinging it open to fully disengage the clips.
• Gently swing open the back glass towards the volume buttons.
• Support the back glass with a clean, sturdy object like a small box to avoid straining the cable.
• Remove the opening picks.

Step 12

Unfasten the middle connector cover

⌕

• Use a tri-point Y000 driver to remove the two 1.3 mm-long screws securing the middle connector cover.

Step 13

Remove the middle connector cover

⌕

• Be careful not to dent or puncture the battery during this step.
• Use blunt-nose tweezers or your fingers to slide the cover towards the left edge of the phone and release its hook from its slot on the logic board.
• Remove the cover.

Step 14

Disconnect the battery

⌕

• Use the point of a spudger to pry up and disconnect the battery press connector.

Step 15

Disconnect the wireless charger

⌕

• Use the point of a spudger to pry up and disconnect the wireless charging coil press connector.

Step 16

Remove the back glass

⌕

• Lift the back glass off the frame and remove it.

Step 17

Remove the Taptic Engine bracket screws

⌕

• Use a Phillips screwdriver to remove the three screws securing the Taptic Engine bracket:
• Two 1.9 mm‑long screws
• One 2.1 mm‑long screw

Step 18

Repair step

⌕

• Use tweezers or your fingers to remove the Taptic Engine bracket.

Step 19

Disconnect the Taptic Engine

⌕

• Use the flat end of a spudger to pry up and disconnect the Taptic Engine press connector.

Step 20

Remove the Taptic Engine screw

⌕

• Use a Phillips screwdriver to remove the 1.8 mm screw securing the Taptic Engine.

Step 21

Remove the Taptic Engine

⌕

• Use blunt-nose tweezers or your fingers to pick up and remove the Taptic Engine.

Step 22

Remove the loudspeaker screws

⌕

• Be careful not to puncture or dent the battery with your screwdriver.
• Use your Phillips screwdriver to remove four of the screws securing the loudspeaker:
• Three 1.5 mm-long screws
• One 3.0 mm-long screw
• Use your tri-point Y000 screwdriver to remove the 1.3 mm-long screw securing a grounding contact and the loudspeaker.
• Use your standoff screwdriver to remove the 3.4 mm-long screw securing the loudspeaker.
• If you don't have a standoff driver, you may use a thin flathead driver—but be careful not to strip the shallow notches in the screw heads.

Step 23

Remove the loudspeaker

⌕

• Grab the loudspeaker and remove it.