iPhone 16 Pro Max Back Glass Replacement

Step 1

Before you begin

⌕

TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Allow your iPhone's battery to drain below 25%, as a charged lithium-ion battery is a potential safety hazard.
Unplug any cables from your iPhone.
Hold the power and either volume buttons, and slide to power off your iPhone.

Step 2

Tape over any cracks

⌕

TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide

View item

If your screen or back glass is badly cracked, lay overlapping strips of packing tape over the glass to protect yourself and make disassembly easier.
Make sure there's a smooth area near the bottom edge that's big enough for a suction cup to stick to.

Step 3

Remove the pentalobe screws

⌕

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tri-point Y000 Screwdriver Referenced by the iFixit guide

View item

Use a P2 pentalobe driver to remove the two 7.4 mm-long screws on either side of the charge port.

Step 4

Mark your opening picks

⌕

TOOL USED ON THIS STEP Coin Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

If inserted too far, an opening pick can damage your device. Follow this step to mark your pick and prevent damage.
Measure 3 mm from the tip and mark the opening pick with a permanent marker.
You can also mark the other corners of the pick with different measurements.
Alternatively, tape a coin to a pick 3 mm from the tip.

Step 5

Create a gap using a suction handle

⌕

TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide

View item

The next two steps show how to create an initial gap using a suction handle.
Use a hair dryer or heat gun to heat the bottom edge of the back glass until it's hot to the touch.
You can also use an iOpener to heat the back glass. Follow these instructions to heat and apply the iOpener properly.

Step 6

Repair step

⌕

TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

Apply a suction handle to the bottom edge of the back glass.
Pull up on the handle with strong, steady force to create a gap between the back glass and the frame.
If a gap doesn't appear, apply more heat to the edge and try again.
Insert the tip of an opening pick into the gap.

Step 7

Back glass information

⌕

TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide

View item

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

As you slice the adhesive securing the back glass in the following steps, don't insert your pick deeper than 3 mm to avoid damaging the following areas:
A delicate cable connecting the back glass to the iPhone, right next to the volume up button. Don't insert your pick here to avoid slicing the cable.
Multiple spring contacts around the perimeter of the iPhone.

Step 8

Separate the bottom edge adhesive

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

Slide the opening pick along the bottom edge to slice the adhesive.
If the adhesive feels difficult to slice, reheat the edge for a minute and try again.
Leave the opening pick in the bottom-left corner to prevent the adhesive from resealing.

Step 9

Heat the left edge

⌕

TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide

View item

Use a hair dryer or heat gun to heat the left edge of the back glass until it's hot to the touch.

Step 10

Separate the left adhesive

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

Insert a second opening pick into the bottom-left corner, close to the existing pick.
Don't insert your pick deeper than 3 mm to avoid damaging the spring contacts.
Slide your pick along the left edge to separate the adhesive and release the metal clips.
You'll hear and feel the metal clips release as you pass them.
Leave this pick inserted in the top-left corner to prevent the adhesive from resealing.

Step 11

Heat the top edge and corner

⌕

TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide

View item

Use a hair dryer or heat gun to heat the top edge and top-right corner of the back glass until it's hot to the touch.

Step 12

Separate the top adhesive

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

Don't insert your pick deeper than 3 mm to avoid damaging the spring contacts.
Insert a third opening pick into the top-left corner.
Slide the opening pick along the top edge and around the top-right corner, stopping above the volume up button.
Leave this pick inserted to prevent the adhesive from resealing.

Step 13

Heat the right edge

⌕

TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide

View item

Use a hair dryer or heat gun to heat the right edge of the back glass until it's hot to the touch.

Step 14

Separate the right adhesive

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

Don't insert your pick deeper than 3 mm to avoid damaging the spring contacts.
Insert a fourth opening pick into the bottom-right corner.
Slide the opening pick around the corner and up the right edge, stopping below the volume down button.
Leave this pick inserted to prevent the adhesive from resealing.

Step 15

Reposition the back glass

⌕

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

At this point, the back glass should be free from the frame. If the back glass feels stuck, go back around the perimeter with your pick to check for missed sections of adhesive or stuck clips.
Swing open the back glass to the right of the iPhone to separate the remaining adhesive.
Support the back glass with a clean, sturdy object.

Step 16

Remove the battery connector cover

⌕

TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

Use a tri-point Y000 driver to remove the three screws securing the battery connector cover:
Two 1.3 mm‑long screws
One 1.0 mm‑long screw

Step 17

Repair step

⌕

TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Lift and remove the battery connector cover.

Step 18

Disconnect the battery

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide

View item

Use the point of a spudger to pry up and disconnect the battery press connector.

Step 19

Remove the back glass connector cover

⌕

TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

Use a tri-point Y000 driver to remove the four screws securing the back glass connector cover:
Two 1.3 mm‑long screws
Two 1.0 mm‑long screws

Step 20

Repair step

⌕

TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Lift the back glass connector cover straight up and remove it.

Step 21

Remove the back glass

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide

View item

Use the point of a spudger to pry up and disconnect the back glass connector.

Step 22

Repair step

⌕

Remove the back glass.

Step 23

Disassembly complete

⌕

Congratulations on completing disassembly! The remaining steps will show how to reassemble your iPhone.
Depending on your iPhone model, some reassembly photos may have minor visual discrepancies. The procedure, however, will be correct for your iPhone.

Step 24

Remove the leftover adhesive

⌕

TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

Work around the fragile grounding clips as you're cleaning the frame. If you bend one out of place, gently bend it back with your fingers or tweezers.
Use blunt nose tweezers or your fingers to remove large pieces of adhesive from the frame perimeter.
Use a spudger to scrape the adhesive residue off of the frame.
If the adhesive feels stubborn, apply some heat using a hair dryer or heat gun and try again.

Step 25

Clean the back glass

⌕

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

If you're reusing your back glass, apply a few drops of highly-concentrated isopropyl alcohol (over 90%) to a microfiber or lint-free cloth and wipe around the perimeter to prepare the surface for new adhesive.

Step 26

Clean the frame

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

Wrap a lint-free cloth or a coffee filter over the point of a spudger and apply a few drops of highly-concentrated isopropyl alcohol (over 90%) to it.
Wipe in one direction along the perimeter of the frame to clean the adhesive residue.
Take your time doing this. A clean frame allows replacement adhesive to lay evenly, ensuring a better bond.

Step 27

Apply the replacement adhesive

⌕

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

Lay the adhesive sheet over the frame to determine its proper orientation.
Use features such as the camera cutout and notches along the top and bottom edges to visualize how the adhesive will lay in the frame.

Step 28

Repair step

⌕

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

Grab the tab in the corner of the adhesive sheet and peel the liner to expose a third of the adhesive.
The exposed adhesive is very sticky. Don't let it touch anything until you're ready to apply it to the frame.
If your adhesive has multiple liners, peel the liner that exposes the side that sticks to the frame.

Step 29

Repair step

⌕

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

Carefully align the exposed edge of the adhesive strip with the corresponding edge of the iPhone's frame.
Once the adhesive is pressed into place, you can't reposition it—you'll have to remove it and start over with new adhesive.
When it's correctly aligned, gently press the exposed adhesive strip onto the frame.

Step 30

Repair step

⌕

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

Continue peeling away the liner from the adhesive, gently pressing the adhesive into place.
If you've correctly aligned the adhesive, the edges will fall perfectly into place.
If your adhesive is slightly misaligned, gently pull the long edges into alignment with the frame.
If the adhesive begins to crease or wrinkle, remove it and start over with fresh adhesive.
If you don't have another set of adhesive strips handy, it's okay to temporarily put your iPhone back together and use it normally without any adhesive. Just keep in mind that your iPhone's water resistance will be compromised until you replace the adhesive.

Step 31

Repair step

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide

View item

Use a spudger to press the adhesive around the entire perimeter of your iPhone.
Work around the fragile grounding clips. If you bend one out of place, gently bend it back with your fingers or tweezers.
Don't press too hard, or you'll stretch and deform the adhesive.

Step 32

Repair step

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

Use a spudger or your fingers to lift the pull tab connected to the large front liner. The pull tab is often in a corner of the liner.
Use the pull tab to peel off the large front liner from the adhesive.
At this point, you may still have a liner covering the perimeter, which prevents the adhesive from accidentally sticking to anything while you're reassembling your iPhone. Don't remove these small release liners just yet.

Step 33

Connect the back glass

⌕

Prop up the back glass along the right edge of your iPhone.

Step 34

Repair step

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide

View item

Use your finger or the flat end of a spudger to press and connect the back glass connector onto the logic board.

Step 35

Connect the battery

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide

View item

Use your finger or a spudger to press and connect the battery press connector onto the logic board.
This is a good point to test your repair before sealing up your iPhone. Power on your iPhone and make sure it works as expected. Power it back down and continue reassembly.
If your iPhone doesn't turn on, connect it to a power source and try again.
If you've replaced the logic board and the screen fails to turn on, you'll need to follow the screen guide to manually connect the display connector.

Step 36

Install the connector covers

⌕

TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

Align the back glass connector cover by its screw holes and lay it in place.

Step 37

Repair step

⌕

TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

Use a tri-point Y000 driver to install the four screws securing the back glass connector cover:
Two 1.3 mm‑long screws
Two 1.0 mm‑long screws

Step 38

Repair step

⌕

TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

Align the battery connector cover by its screw holes and lay it in place.

Step 39

Repair step

⌕

TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

Use a tri-point Y000 driver to install the three screws securing the battery connector cover:
Two 1.3 mm‑long screws
One 1.0 mm‑long screw

Step 40

Remove the final adhesive liners

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

Use your fingers or a spudger to peel away all perimeter liners, exposing the adhesive.
As you remove the liners, make sure nothing touches the exposed adhesive.
Check the frame and back glass for any stray liners and remove them. There should be no liners remaining.

Step 41

Install the back glass

⌕

Lower the back glass onto the frame, beginning with the top edge.
If you feel resistance, a perimeter clip may have bent out of place and is being crushed by the frame. Look at the point of resistance and gently straighten any bent clips.
Press along the edges of the iPhone until the back glass sits flush against the frame.

Step 42

Apply heat to the perimeter

⌕

TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iOpener Referenced by the iFixit guide

View item

Use a hair dryer, heat gun, or an iOpener to heat the back glass perimeter until it's slightly too hot to touch.
The heat softens the adhesive and helps create a better bond.

Step 43

Apply pressure to the perimeter

⌕

Use your fingers to firmly squeeze around the perimeter of the iPhone.

Step 44

Repair step

⌕

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

Place your iPhone screen-side down on a clean, flat work surface.
Lay a strip of tape around the perimeter of the back glass to protect the finish.
Stack coins around the perimeter of the back glass until you create a wall that's as tall as the rear camera protrusions.
Alternatively, you can use vise clamps around the perimeter of your device to set the new adhesive.

Step 45

Repair step

⌕

TOOL USED ON THIS STEP Heavy Books Referenced by the iFixit guide

View item

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

Place 3-4 heavy books squarely on top of your iPhone.
The coins may leave a slight impression on the bottom book cover, so don't use anything valuable.
Leave the books in place for about 30 minutes.
The pressure will help activate the adhesive.

Step 46

Install the pentalobe screws

⌕

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tri-point Y000 Screwdriver Referenced by the iFixit guide

View item

Use a P2 pentalobe driver to install the two 7.4 mm-long screws on either side of the charge port.