FIXONIC
Repair starts here.Sign inCreate account Live auctionsRepair HubRepair guides
SellSavedMy Fixonic
FIXONICrepair marketplace
Home/ Repair guides/ iPhone 16 Pro Max Charge Port Replacement
Official iFixit API visual reference

iPhone 16 Pro Max Charge Port Replacement

This guide shows how to remove and replace the...

Apple iPhone 16 Pro Max Moderate 1 - 3 hours Guide 178826
Open the authorised source
Licensed iFixit integration

This attributed iFixit guide is displayed through Fixonic's recorded commercial API permission. iFixit remains the independent source and author of the procedure.

Guide overview

Before you begin

This guide shows how to remove and replace the USB-C charge port in your iPhone 16 Pro Max. If your port feels loose, or you experience connectivity or charging issues when you plug in your iPhone, you may need to replace your charge port. Before you perform this repair, try cleaning the port first. You may not have a broken port—just a dirty one. You'll need replacement microphone and back glass adhesives to complete this repair.

Step 1

Before you begin

iPhone 16 Pro Max Charge Port Replacement — Before you begin ⌕
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • Allow your iPhone's battery to drain below 25%, as a charged lithium-ion battery is a potential safety hazard.
  • Unplug any cables from your iPhone.
  • Hold the power and either volume buttons, and slide to power off your iPhone.
Step 2

Tape over any cracks

iPhone 16 Pro Max Charge Port Replacement — Tape over any cracks ⌕
Suction Handle
TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide
View item
  • If your screen or back glass is badly cracked, lay overlapping strips of packing tape over the glass to protect yourself and make disassembly easier.
  • Make sure there's a smooth area near the bottom edge that's big enough for a suction cup to stick to.
Step 3

Remove the pentalobe screws

iPhone 16 Pro Max Charge Port Replacement — Remove the pentalobe screws ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Use a P2 pentalobe driver to remove the two 7.4 mm-long screws on either side of the charge port.
Step 4

Mark your opening picks

iPhone 16 Pro Max Charge Port Replacement — Mark your opening picks ⌕
Coin
TOOL USED ON THIS STEP Coin Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • If inserted too far, an opening pick can damage your device. Follow this step to mark your pick and prevent damage.
  • Measure 3 mm from the tip and mark the opening pick with a permanent marker.
  • You can also mark the other corners of the pick with different measurements.
  • Alternatively, tape a coin to a pick 3 mm from the tip.
Step 5

Create a gap using a suction handle

iPhone 16 Pro Max Charge Port Replacement — Create a gap using a suction handle ⌕
Heat Gun
TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide
View item
Suction Handle
TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide
View item
  • The next two steps show how to create an initial gap using a suction handle.
  • Use a hair dryer or heat gun to heat the bottom edge of the back glass until it's hot to the touch.
  • You can also use an iOpener to heat the back glass. Follow these instructions to heat and apply the iOpener properly.
Step 6

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
Suction Handle
TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • Apply a suction handle to the bottom edge of the back glass.
  • Pull up on the handle with strong, steady force to create a gap between the back glass and the frame.
  • If a gap doesn't appear, apply more heat to the edge and try again.
  • Insert the tip of an opening pick into the gap.
Step 7

Back glass information

iPhone 16 Pro Max Charge Port Replacement — Back glass information ⌕
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • As you slice the adhesive securing the back glass in the following steps, don't insert your pick deeper than 3 mm to avoid damaging the following areas:
  • A delicate cable connecting the back glass to the iPhone, right next to the volume up button. Don't insert your pick here to avoid slicing the cable.
  • Multiple spring contacts around the perimeter of the iPhone.
Step 8

Separate the bottom edge adhesive

iPhone 16 Pro Max Charge Port Replacement — Separate the bottom edge adhesive ⌕
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • Slide the opening pick along the bottom edge to slice the adhesive.
  • If the adhesive feels difficult to slice, reheat the edge for a minute and try again.
  • Leave the opening pick in the bottom-left corner to prevent the adhesive from resealing.
Step 9

Heat the left edge

iPhone 16 Pro Max Charge Port Replacement — Heat the left edge ⌕
Heat Gun
TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide
View item
  • Use a hair dryer or heat gun to heat the left edge of the back glass until it's hot to the touch.
Step 10

Separate the left adhesive

iPhone 16 Pro Max Charge Port Replacement — Separate the left adhesive ⌕
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • Insert a second opening pick into the bottom-left corner, close to the existing pick.
  • Don't insert your pick deeper than 3 mm to avoid damaging the spring contacts.
  • Slide your pick along the left edge to separate the adhesive and release the metal clips.
  • You'll hear and feel the metal clips release as you pass them.
  • Leave this pick inserted in the top-left corner to prevent the adhesive from resealing.
Step 11

Heat the top edge and corner

iPhone 16 Pro Max Charge Port Replacement — Heat the top edge and corner ⌕
Heat Gun
TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide
View item
  • Use a hair dryer or heat gun to heat the top edge and top-right corner of the back glass until it's hot to the touch.
Step 12

Separate the top adhesive

iPhone 16 Pro Max Charge Port Replacement — Separate the top adhesive ⌕
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • Don't insert your pick deeper than 3 mm to avoid damaging the spring contacts.
  • Insert a third opening pick into the top-left corner.
  • Slide the opening pick along the top edge and around the top-right corner, stopping above the volume up button.
  • Leave this pick inserted to prevent the adhesive from resealing.
Step 13

Heat the right edge

iPhone 16 Pro Max Charge Port Replacement — Heat the right edge ⌕
Heat Gun
TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide
View item
  • Use a hair dryer or heat gun to heat the right edge of the back glass until it's hot to the touch.
Step 14

Separate the right adhesive

iPhone 16 Pro Max Charge Port Replacement — Separate the right adhesive ⌕
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • Don't insert your pick deeper than 3 mm to avoid damaging the spring contacts.
  • Insert a fourth opening pick into the bottom-right corner.
  • Slide the opening pick around the corner and up the right edge, stopping below the volume down button.
  • Leave this pick inserted to prevent the adhesive from resealing.
Step 15

Reposition the back glass

iPhone 16 Pro Max Charge Port Replacement — Reposition the back glass ⌕
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • At this point, the back glass should be free from the frame. If the back glass feels stuck, go back around the perimeter with your pick to check for missed sections of adhesive or stuck clips.
  • Swing open the back glass to the right of the iPhone to separate the remaining adhesive.
  • Support the back glass with a clean, sturdy object.
Step 16

Remove the battery connector cover

iPhone 16 Pro Max Charge Port Replacement — Remove the battery connector cover ⌕
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
  • Use a tri-point Y000 driver to remove the three screws securing the battery connector cover:
  • Two 1.3 mm‑long screws
  • One 1.0 mm‑long screw
Step 17

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • Lift and remove the battery connector cover.
Step 18

Disconnect the battery

iPhone 16 Pro Max Charge Port Replacement — Disconnect the battery ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
  • Use the point of a spudger to pry up and disconnect the battery press connector.
Step 19

Remove the back glass connector cover

iPhone 16 Pro Max Charge Port Replacement — Remove the back glass connector cover ⌕
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
  • Use a tri-point Y000 driver to remove the four screws securing the back glass connector cover:
  • Two 1.3 mm‑long screws
  • Two 1.0 mm‑long screws
Step 20

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • Lift the back glass connector cover straight up and remove it.
Step 21

Remove the back glass

iPhone 16 Pro Max Charge Port Replacement — Remove the back glass ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
  • Use the point of a spudger to pry up and disconnect the back glass connector.
Step 22

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
  • Remove the back glass.
Step 23

Remove the Taptic Engine cover

iPhone 16 Pro Max Charge Port Replacement — Remove the Taptic Engine cover ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Use a Phillips screwdriver to remove the three screws securing the Taptic Engine cover:
  • One 2.9 mm‑long screw
  • One 1.3 mm‑long screw
  • One 2.4 mm‑long screw
Step 24

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
  • Use tweezers or your fingers to lift the top edge of the Taptic Engine cover.
  • Once the bottom edge unlatches from the frame, remove the Taptic Engine cover.
Step 25

Loosen the lower assembly cable

iPhone 16 Pro Max Charge Port Replacement — Loosen the lower assembly cable ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
  • Use the point of a spudger to pry up and disconnect the lower assembly cable from the logic board.
Step 26

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
  • Use the point of a spudger to pry up and disconnect the two connectors near the bottom right edge of the frame.
Step 27

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
  • Remove the two screws securing the lower assembly cable:
  • One 1.0 mm‑long tri-point Y000 screw
  • One 1.3 mm‑long Phillips screw
Step 28

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • Use a hair dryer to heat up the lower assembly cable section on top of the Taptic Engine until it's hot to the touch.
Step 29

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
  • Slide an opening pick under the lower assembly cable to separate it from the Taptic Engine.
  • Carefully bend the cable out of the way so you can access the Taptic Engine.
Step 30

Remove the Taptic Engine

iPhone 16 Pro Max Charge Port Replacement — Remove the Taptic Engine ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Use a Phillips screwdriver to remove the 2.1 mm‑long screw securing the Taptic Engine.
Step 31

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • Use the point of a spudger to pivot the corner bracket up.
Step 32

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • Slide the tip of an opening pick along the top edge of the Taptic Engine to separate the plastic buffer strip adhered to it.
Step 33

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • Use the point of a spudger to pry up the Taptic Engine.
  • Be careful not to pry against the battery.
  • Remove the Taptic Engine.
Step 34

Remove the loudspeaker

iPhone 16 Pro Max Charge Port Replacement — Remove the loudspeaker ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Remove the four screws securing the loudspeaker:
  • One 1.7 mm‑long Phillips screw
  • One 1.5 mm‑long Phillips screw
  • One 4.1 mm‑long standoff screw
  • One 1.3 mm‑long tri-point Y000 screw
Step 35

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
  • Insert the point of a spudger underneath the loudspeaker's bottom-right screw hole.
  • Pry up and remove the loudspeaker.
Step 36

Remove the bottom microphone

iPhone 16 Pro Max Charge Port Replacement — Remove the bottom microphone ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Remove the three screws securing the bottom microphone:
  • One 3.4 mm‑long standoff screw
  • One 3 mm‑long standoff screw
  • One 1.4 mm‑long tri-point Y000 screw
Step 37

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • Use the flat end of a spudger to pry up the bottom microphone.
  • Don't pry against the battery, or you may damage it.
  • You'll feel some resistance as the microphone releases from its adhesive gasket.
  • Remove the bottom microphone.
Step 38

Remove the adhesive gasket

iPhone 16 Pro Max Charge Port Replacement — Remove the adhesive gasket ⌕
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
  • Use tweezers or your fingers to remove the old adhesive gasket from the bottom of the frame.
Step 39

Remove the charge port

iPhone 16 Pro Max Charge Port Replacement — Remove the charge port ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Use a Phillips screwdriver to remove the two 3.3 mm‑long screws securing the charge port to the frame.
  • These screws are tight and can be difficult to reach. Angle your screwdriver at as shallow of an angle as you can, but be careful not to press against the battery.
Step 40

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • The charge port has an adhesive gasket that seals it against the bottom of the frame. It's also tucked behind two prongs, which prevents you from pulling the port away from the frame.
  • Insert the point of a spudger under one side of the charge port.
  • Pry up gently to separate the gasket and lift the port up.
  • Repeat on the other side to fully loosen the port.
Step 41

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Remove the charge port.
  • The two screw posts underneath the charge port have grounding clips on them. If the clips fell off, be sure to place them back onto their posts. The clips should face towards the bottom of the iPhone.
Step 42

Disassembly complete

iPhone 16 Pro Max Charge Port Replacement — Disassembly complete ⌕
  • Congratulations on completing disassembly! The remaining steps will show how to reassemble your iPhone.
  • Depending on your iPhone model, some reassembly photos may have minor visual discrepancies. The procedure, however, will be correct for your iPhone.
Step 43

Check the black prongs for alignment

iPhone 16 Pro Max Charge Port Replacement — Check the black prongs for alignment ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • Make sure the two black prongs are standing straight up. If they were bent when you removed the charge port, use the point of a spudger to carefully straighten them.
Step 44

Install the charge port

iPhone 16 Pro Max Charge Port Replacement — Install the charge port ⌕
  • Angle the bottom edge of the charge port into its recess and press the charge port in place.
Step 45

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Use a pentalobe P2 driver to temporarily install the two external pentalobe screws.
  • This pulls the loose charge port into alignment.
Step 46

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Use a Phillips screwdriver to install the two 3.3 mm‑long screws securing the charge port to the frame.
  • Be careful not to press the screwdriver against the battery.
Step 47

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Use a pentalobe P2 driver to remove the two temporary pentalobe screws.
  • If you forget to remove these screws, the back glass won't install properly.
Step 48

Install the bottom microphone

iPhone 16 Pro Max Charge Port Replacement — Install the bottom microphone ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • Peel the white liner from the microphone adhesive gasket
  • Align the gasket to the frame's microphone cutout and use a spudger to press it in place.
  • Remove the remaining liner from the adhesive.
Step 49

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
  • Insert the microphone at a downward angle into its recess before pressing it flat to the frame.
Step 50

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Install the three screws securing the bottom microphone:
  • One 3.4 mm‑long standoff screw
  • One 3 mm‑long standoff screw
  • One 1.4 mm‑long tri-point Y000 screw
Step 51

Install the loudspeaker

iPhone 16 Pro Max Charge Port Replacement — Install the loudspeaker ⌕
  • Angle the bottom edge of the loudspeaker towards the frame.
  • Press the loudspeaker into its recess.
Step 52

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Install the four screws securing the loudspeaker:
  • One 1.7 mm‑long Phillips screw
  • One 1.5 mm‑long Phillips screw
  • One 4.1 mm‑long standoff screw
  • One 1.3 mm‑long tri-point Y000 screw
Step 53

Install the Taptic Engine

iPhone 16 Pro Max Charge Port Replacement — Install the Taptic Engine ⌕
  • Lay the Taptic Engine in its recess.
Step 54

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
  • Use your finger to pivot the corner bracket down into place.
Step 55

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Use a Phillips screwdriver to install the 2.1 mm‑long screw securing the Taptic Engine.
Step 56

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • Use your finger to gently press the lower assembly cable onto the top of the Taptic Engine.
Step 57

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
  • Install the two screws securing the lower assembly cable:
  • One 1.0 mm‑long tri-point Y000 screw
  • One 1.3 mm‑long Phillips screw
Step 58

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
  • Use your finger or a spudger to press and connect the two lower assembly cable connectors.
Step 59

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Lay the Taptic Engine cover in place and align it by its screw holes.
  • Make sure the bottom edge of the cover latches properly to the frame.
Step 60

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Use a Phillips screwdriver to install the three screws securing the Taptic Engine cover:
  • One 2.9 mm‑long screw
  • One 1.3 mm‑long screw
  • One 2.4 mm‑long screw
Step 61

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
  • Use your finger or a spudger to press the assembly cable connector onto the logic board.
Step 62

Remove the leftover adhesive

iPhone 16 Pro Max Charge Port Replacement — Remove the leftover adhesive ⌕
Heat Gun
TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide
View item
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • Work around the fragile grounding clips as you're cleaning the frame. If you bend one out of place, gently bend it back with your fingers or tweezers.
  • Use blunt nose tweezers or your fingers to remove large pieces of adhesive from the frame perimeter.
  • Use a spudger to scrape the adhesive residue off of the frame.
  • If the adhesive feels stubborn, apply some heat using a hair dryer or heat gun and try again.
Step 63

Clean the back glass

iPhone 16 Pro Max Charge Port Replacement — Clean the back glass ⌕
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • If you're reusing your back glass, apply a few drops of highly-concentrated isopropyl alcohol (over 90%) to a microfiber or lint-free cloth and wipe around the perimeter to prepare the surface for new adhesive.
Step 64

Clean the frame

iPhone 16 Pro Max Charge Port Replacement — Clean the frame ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • Wrap a lint-free cloth or a coffee filter over the point of a spudger and apply a few drops of highly-concentrated isopropyl alcohol (over 90%) to it.
  • Wipe in one direction along the perimeter of the frame to clean the adhesive residue.
  • Take your time doing this. A clean frame allows replacement adhesive to lay evenly, ensuring a better bond.
Step 65

Apply the replacement adhesive

iPhone 16 Pro Max Charge Port Replacement — Apply the replacement adhesive ⌕
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • Lay the adhesive sheet over the frame to determine its proper orientation.
  • Use features such as the camera cutout and notches along the top and bottom edges to visualize how the adhesive will lay in the frame.
Step 66

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • Grab the tab in the corner of the adhesive sheet and peel the liner to expose a third of the adhesive.
  • The exposed adhesive is very sticky. Don't let it touch anything until you're ready to apply it to the frame.
  • If your adhesive has multiple liners, peel the liner that exposes the side that sticks to the frame.
Step 67

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • Carefully align the exposed edge of the adhesive strip with the corresponding edge of the iPhone's frame.
  • Once the adhesive is pressed into place, you can't reposition it—you'll have to remove it and start over with new adhesive.
  • When it's correctly aligned, gently press the exposed adhesive strip onto the frame.
Step 68

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • Continue peeling away the liner from the adhesive, gently pressing the adhesive into place.
  • If you've correctly aligned the adhesive, the edges will fall perfectly into place.
  • If your adhesive is slightly misaligned, gently pull the long edges into alignment with the frame.
  • If the adhesive begins to crease or wrinkle, remove it and start over with fresh adhesive.
  • If you don't have another set of adhesive strips handy, it's okay to temporarily put your iPhone back together and use it normally without any adhesive. Just keep in mind that your iPhone's water resistance will be compromised until you replace the adhesive.
Step 69

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use a spudger to press the adhesive around the entire perimeter of your iPhone.
  • Work around the fragile grounding clips. If you bend one out of place, gently bend it back with your fingers or tweezers.
  • Don't press too hard, or you'll stretch and deform the adhesive.
Step 70

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • Use a spudger or your fingers to lift the pull tab connected to the large front liner. The pull tab is often in a corner of the liner.
  • Use the pull tab to peel off the large front liner from the adhesive.
  • At this point, you may still have a liner covering the perimeter, which prevents the adhesive from accidentally sticking to anything while you're reassembling your iPhone. Don't remove these small release liners just yet.
Step 71

Connect the back glass

iPhone 16 Pro Max Charge Port Replacement — Connect the back glass ⌕
  • Prop up the back glass along the right edge of your iPhone.
Step 72

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
  • Use your finger or the flat end of a spudger to press and connect the back glass connector onto the logic board.
Step 73

Connect the battery

iPhone 16 Pro Max Charge Port Replacement — Connect the battery ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
  • Use your finger or a spudger to press and connect the battery press connector onto the logic board.
  • This is a good point to test your repair before sealing up your iPhone. Power on your iPhone and make sure it works as expected. Power it back down and continue reassembly.
  • If your iPhone doesn't turn on, connect it to a power source and try again.
  • If you've replaced the logic board and the screen fails to turn on, you'll need to follow the screen guide to manually connect the display connector.
Step 74

Install the connector covers

iPhone 16 Pro Max Charge Port Replacement — Install the connector covers ⌕
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
  • Align the back glass connector cover by its screw holes and lay it in place.
Step 75

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
  • Use a tri-point Y000 driver to install the four screws securing the back glass connector cover:
  • Two 1.3 mm‑long screws
  • Two 1.0 mm‑long screws
Step 76

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
  • Align the battery connector cover by its screw holes and lay it in place.
Step 77

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
ESD Safe Blunt Nose Tweezers
TOOL USED ON THIS STEP ESD Safe Blunt Nose Tweezers Referenced by the iFixit guide
View item
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
  • Use a tri-point Y000 driver to install the three screws securing the battery connector cover:
  • Two 1.3 mm‑long screws
  • One 1.0 mm‑long screw
Step 78

Remove the final adhesive liners

iPhone 16 Pro Max Charge Port Replacement — Remove the final adhesive liners ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • Use your fingers or a spudger to peel away all perimeter liners, exposing the adhesive.
  • As you remove the liners, make sure nothing touches the exposed adhesive.
  • Check the frame and back glass for any stray liners and remove them. There should be no liners remaining.
Step 79

Install the back glass

iPhone 16 Pro Max Charge Port Replacement — Install the back glass ⌕
  • Lower the back glass onto the frame, beginning with the top edge.
  • If you feel resistance, a perimeter clip may have bent out of place and is being crushed by the frame. Look at the point of resistance and gently straighten any bent clips.
  • Press along the edges of the iPhone until the back glass sits flush against the frame.
Step 80

Apply heat to the perimeter

iPhone 16 Pro Max Charge Port Replacement — Apply heat to the perimeter ⌕
Heat Gun
TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide
View item
iOpener
TOOL USED ON THIS STEP iOpener Referenced by the iFixit guide
View item
  • Use a hair dryer, heat gun, or an iOpener to heat the back glass perimeter until it's slightly too hot to touch.
  • The heat softens the adhesive and helps create a better bond.
Step 81

Apply pressure to the perimeter

iPhone 16 Pro Max Charge Port Replacement — Apply pressure to the perimeter ⌕
  • Use your fingers to firmly squeeze around the perimeter of the iPhone.
Step 82

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • Place your iPhone screen-side down on a clean, flat work surface.
  • Lay a strip of tape around the perimeter of the back glass to protect the finish.
  • Stack coins around the perimeter of the back glass until you create a wall that's as tall as the rear camera protrusions.
  • Alternatively, you can use vise clamps around the perimeter of your device to set the new adhesive.
Step 83

Repair step

iPhone 16 Pro Max Charge Port Replacement — repair step ⌕
Heavy Books
TOOL USED ON THIS STEP Heavy Books Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • Place 3-4 heavy books squarely on top of your iPhone.
  • The coins may leave a slight impression on the bottom book cover, so don't use anything valuable.
  • Leave the books in place for about 30 minutes.
  • The pressure will help activate the adhesive.
Step 84

Install the pentalobe screws

iPhone 16 Pro Max Charge Port Replacement — Install the pentalobe screws ⌕
P2 Pentalobe Screwdriver iPhone
TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide
View item
Phillips #000 Screwdriver
TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide
View item
  • Use a P2 pentalobe driver to install the two 7.4 mm-long screws on either side of the charge port.