FIXONICBefore you begin
Prerequisite guide to remove the battery in an iPhone 16 Pro.
Official iFixit API visual reference
Open the authorised source
iPhone 16 Pro Battery Removal
Prerequisite guide to remove the battery in an...
Apple iPhone 16 Pro
Moderate
1 - 3 hours
Guide 181231
Licensed iFixit integration
This attributed iFixit guide is displayed through Fixonic's recorded commercial API permission. iFixit remains the independent source and author of the procedure.
Prepare the phone for disassembly
Tape over any cracks
Mark your opening picks
Remove the pentalobe screws
Heat the bottom edge
Insert an opening pick
- Apply a suction handle to the bottom edge of the back glass, above the USB-C port.
- Pull up on the handle with a strong, steady force to create a gap between the back glass and the frame.
- Insert the tip of an opening pick into the gap.
Back glass information
- There's a delicate cable connecting the back glass to the phone, right next to the volume up button. Don't insert your pick here to avoid slicing the cable.
- There are multiple spring contacts around the perimeter of the phone. Be extra careful not to insert your pick deeper than suggested in each step to avoid bending these contacts.
Separate the bottom edge adhesive
- Slide your pick back and forth along the bottom edge to separate the adhesive.
- Leave your pick inserted in the bottom right corner to prevent the adhesive from resealing.
Heat the right edge
- Heat the right edge of the back glass until it's hot to the touch.
Separate the bottom right corner adhesive
- Slide your pick around the bottom right corner and halfway up the right edge, or until you feel a hard stop at a clip securing the back glass.
- Leave this pick inserted to prevent the adhesive from resealing.
Heat the left edge
- Heat the left edge of the back glass until it's hot to the touch.
Separate the left edge adhesive
- Insert a second opening pick at the bottom edge.
- Slide the second pick around the bottom left corner and along the left edge of the screen to separate the adhesive and release the metal clips.
- Leave this pick inserted at the top left corner to prevent the adhesive from resealing.
Heat the top edge
- Heat the top edge of the back glass, including the area around the volume buttons, until it's hot to the touch.
Separate the top edge adhesive
- Slide your opening pick across the top edge and around the top right corner to the volume up button to separate the adhesive.
Swing open the back glass
- Gently swing open the back glass towards the volume buttons.
- Support the back glass with a clean, sturdy object like a small box to avoid straining the cable.
- Remove the opening picks.
Disconnect the battery
- Use a tri-point Y000 screwdriver to remove the three screws securing the lower connector cover:
- Two 1.2 mm‑long screws
- One 1.0 mm‑long screw
Repair step
Repair step
Disconnect the back glass
- Use a tri-point Y000 screwdriver to remove the four screws securing the upper connector cover:
- Two 1.0 mm‑long screws
- One 1.2 mm‑long screw
- One 1.6 mm‑long screw
Repair step
Repair step
Remove the back glass
- Lift the back glass off the frame and remove it.
Remove the Taptic Engine cover
- Use a Phillips screwdriver to remove the three screws securing the Taptic Engine cover:
- One 3.0 mm‑long screw
- Two 1.7 mm‑long screws
Repair step
- Use tweezers or your fingers to lift the top edge of the Taptic Engine cover.
- Once the bottom edge unlatches from the frame, remove the Taptic Engine cover.
Disconnect the lower assembly cable
Repair step
Repair step
Repair step
Repair step
- Slide an opening pick under the lower assembly cable to separate it from the Taptic Engine.
- Carefully bend the cable out of the way so you can access the Taptic Engine.
Remove the Taptic Engine
Repair step
Repair step
Remove the loudspeaker
- Remove the four screws securing the loudspeaker:
- Two 1.6 mm‑long Phillips screws
- One 2.0 mm‑long Phillips screw
- One 1.3 mm‑long tri-point Y000 screw
Repair step
Battery adhesive information
Remove the battery
Repair step
Repair step
- Use tweezers or your fingers to grab the pull tab and pull it down so it's flat against the frame.
- Slowly pull the adhesive out from under the battery at as low of an angle as possible.
Repair step
Repair step
- If you removed all three stretch release adhesive strips, congratulations! Lift and remove the battery.
Alternate method to remove the battery
- Lift the bottom edge of the frame to tilt the phone.
- Use a pipette or a syringe to apply 2–3 drops of high concentration (>90%) isopropyl alcohol along the bottom edge of the battery, close to where each broken adhesive strip came out.
- Wait one minute for the isopropyl alcohol to flow under the battery and soften the adhesive.
Repair step
- Insert the tip of an opening pick between the bottom of the battery and the frame.
- Insert a second opening pick between the left edge of the battery and the frame. Use this pick to pry the battery upwards slowly with steady force. Work your way up the edge of the battery, giving the adhesive time to release.
- Once the adhesive loosens, grab and remove the battery.