iPhone 16 Pro Charging Port Removal

Step 1

Prepare the phone for disassembly

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

• Allow the phone's battery to drain below 25%, as a charged lithium-ion battery is a potential safety hazard.
• Unplug any cables from the phone.
• Hold the power and either volume buttons and slide to power off the phone.

Step 2

Tape over any cracks

⌕

TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide

View item

• If the screen or back glass is badly cracked, lay overlapping strips of packing tape over the glass to protect yourself and make disassembly easier.
• Make sure there's a smooth area near the bottom edge that's big enough for a suction cup to stick to.

Step 3

Mark your opening picks

⌕

TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• If inserted too far, an opening pick can damage your device. Follow this step to mark your pick and prevent damage.
• Measure 3 mm from the tip and mark the opening pick with a permanent marker.
• You can also mark the other corners of the pick with different measurements.
• Alternatively, tape a coin to a pick 3 mm from the tip.

Step 4

Remove the pentalobe screws

⌕

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide

View item

• Use a P2 pentalobe screwdriver to remove the two 7.4 mm‑long screws on either side of the USB-C port.

Step 5

Remove the charging port

⌕

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide

View item

• Use a standoff screwdriver to remove the 3.6 mm‑long screw securing the charging port to the frame.

Step 6

Repair step

⌕

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Phillips #000 Screwdriver Referenced by the iFixit guide

View item

• Use a Phillips screwdriver to remove the two 3.4 mm‑long screws securing the charging port to the frame.
• These screws are tight and can be difficult to reach. Angle your screwdriver at as shallow of an angle as you can.

Step 7

Repair step

⌕

TOOL USED ON THIS STEP Tri-point Y000 Screwdriver Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP P2 Pentalobe Screwdriver iPhone Referenced by the iFixit guide

View item

• Use a tri-point Y000 screwdriver to remove the 1.3 mm‑long screw securing the charging port to the frame.

Step 8

Repair step

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

iF

TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide

View item

• The charging port has an adhesive gasket that seals it against the bottom and edge of the frame. It's also tucked behind two prongs, which prevents you from pulling the port away from the frame.
• Insert the point of a spudger under one side of the charging port.
• Pry up gently to separate the gasket and lift the port up.

Step 9

Repair step

⌕

• Don't pull the port directly away from its cut-out in the frame. There are two prongs holding it in place.
• Pull the charging port away from the microphone.
• Remove the charging port.