Home/ Repair guides/ 2015 Ford C-Max Windshield Wiper Replacement

Official iFixit API visual reference

2015 Ford C-Max Windshield Wiper Replacement

If your 2015 Ford C-Max (also applicable to...

iFixit Library Ford C Max Very easy 10 minutes Guide 197221

Licensed iFixit integration

This attributed iFixit guide is displayed through Fixonic's recorded commercial API permission. iFixit remains the independent source and author of the procedure.

Guide overview

Before you begin

If your 2015 Ford C-Max (also applicable to 2013–2018 models) wipers are leaving streaks, skipping across the glass, or failing to clear rain effectively, use this guide to replace the front windshield wiper blades. The front windshield wipers maintain clear visibility by removing rain, snow, and debris from the windshield. Over time, the rubber blades can wear out, crack, or lose flexibility, leading to poor contact with the glass and reduced visibility in wet conditions. This guide will show you how to safely remove the old wiper blades and install new ones without damaging the wiper arms or windshield. For reference, consult your owner’s manual for the correct wiper blade sizes and compatible replacements.

Step 1

Repair step

⌕

The default wiper position keeps the blades tucked beneath the hood, making them difficult to access. These images show the wipers in their stowed position, viewed from both inside and outside the vehicle.

Step 2

Repair step

⌕

Press the ignition button without pressing the brake pedal to turn on the vehicle’s auxiliary power.
This powers the electronics without starting the engine.

Step 3

Repair step

⌕

Within three seconds of turning on auxiliary power, push the wiper control stalk on the right side of the steering wheel downward once to activate the wipers.
This moves them into service mode, positioning the blades vertically for easier access.
Once they stop moving, press the ignition button again to turn the car off.
The second and third images show the wipers in the service position.

Step 4

Repair step

⌕

Squeeze the release clips on the wiper adapter while swiveling the clasp outward to unlock it.
Perform this action on both front wipers.
The first image shows where to press, and the second shows the adapter flipped open.
These adapter instructions are specific to the Rain-X Rugged XL wipers. Follow your specific wiper manufacturer's instructions.

Step 5

Repair step

⌕

Squeeze the sides of the adapter to release it.
Then lift it straight up to remove.
Perform this action on both front wipers.
The first image shows where to squeeze, and the second shows the adapter being lifted off.

Step 6

Repair step

⌕

Pull the blue insert straight out from the adapter to remove it.
Perform this action on both front wipers.

Step 7

Repair step

⌕

Squeeze the pressure release tabs and rotate the wiper blade outward to unlock it.
Once released, lift the blade off the mounting tab to remove it completely.

Step 8

Repair step

⌕

Align the bottom edge of the new wiper as shown in the first image.
Seat the wiper fully onto the mounting tab, as seen in the second image.
Close the top clasp to secure the new wiper in place.

Step 9

Repair step

⌕

Squeeze the pressure tabs on the passenger-side wiper and rotate the blade toward the windshield to release it.
Once released, lift the old wiper off to remove it completely.
This step is identical to the driver's side front wiper.

Step 10

Repair step

⌕

Align the bottom edge of the new passenger-side wiper as shown in the first image.
Seat the wiper fully onto the mounting tab, as seen in the second image.
Close the top clasp to secure the new wiper in place.
This step is identical to the driver's side front wiper.

Step 11

Repair step

⌕

Remove the yellow protective covers from your new wiper blades.
Place the wipers gently on the windshield. Do not let the wipers slam back against the windshield.
Perform this step on both the driver's side and passenger side wipers.

Step 12

Repair step

⌕

Start the car by pressing the brake pedal and the ignition.
Push the wiper control stalk downward (on the right side of the steering wheel) to activate the wipers. This will move the blades into their stowed position.
Turn the car off by pressing the ignition button again once the blades are stowed.