Home/ Repair guides/ 2012 Audi A5 Spark Plug Replacement

Official iFixit API visual reference

2012 Audi A5 Spark Plug Replacement

If you drive a 2012 Audi A5 and are...

iFixit Library Audi A5 Moderate 1 - 2 hours Guide 198688

Licensed iFixit integration

This attributed iFixit guide is displayed through Fixonic's recorded commercial API permission. iFixit remains the independent source and author of the procedure.

Guide overview

Before you begin

If you drive a 2012 Audi A5 and are experiencing decreased fuel economy, are struggling to start your engine, or are experiencing poor acceleration, it may be due to faulty spark plugs. This guide will explain how to replace the spark plugs for a 2012 Audi A5. This includes locating the installed spark plugs, removing the faulty spark plug(s), and installing new spark plug(s). Spark plugs are necessary for the function of the car's engine because they ignite the fuel within the engine's cylinders to drive the pistons. This energy is then transferred to the wheels allowing the car to drive forward. These typically need to be replaced every 30,000 to 100,000 miles. As is common for automotive repairs, it is imperative to turn off the car, allow for the engine to cool, and disconnect the car battery before beginning work on the engine. Park the car on level ground and engage the parking brake. Wait at least 30 minutes after shutting off the engine before beginning the repair to allow for the engine to cool.

Step 1

Repair step

⌕

TOOL USED ON THIS STEP Metal Spudger Referenced by the iFixit guide

View item

Pull the lever on the driver door to open the hood.
Opening the hood of the car before beginning the replacement in order to allow for the engine to cool more quickly.
Caution: Be careful not to touch the engine soon after running the vehicle because it may be considerably hot.

Step 2

Repair step

⌕

TOOL USED ON THIS STEP Metal Spudger Referenced by the iFixit guide

View item

Move to the rear of the car.
Open the trunk.
Grasp the handle on the floor of the trunk and lift the floor panel to access the spare tire.

Step 3

Repair step

⌕

Remove the center hold-down by turning it counterclockwise.
Move the spare tire out of the well and place to the side.

Step 4

Repair step

⌕

TOOL USED ON THIS STEP Metal Spudger Referenced by the iFixit guide

View item

Grasp the outside edges of the panel beneath the spare tire or the central hole and pull it upwards.
This will uncover the car battery compartment.

Step 5

Repair step

⌕

TOOL USED ON THIS STEP Metal Spudger Referenced by the iFixit guide

View item

Locate the battery connection clamp on the innermost right corner of the trunk.
Loosen the negative (–) clamp with a 10 mm wrench by rotating the securing bolt counterclockwise.
Set the cable aside.

Step 6

Repair step

⌕

TOOL USED ON THIS STEP Metal Spudger Referenced by the iFixit guide

View item

Move to the front of the car.
Remove the plastic engine cover:
Pull up on the front edge to release the front clip.
Pull up on the rear edge to release the rear clip.
Lift the cover off and set it aside.

Step 7

Repair step

⌕

TOOL USED ON THIS STEP Metal Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP T30 Torx Screwdriver Bit Referenced by the iFixit guide

View item

Using a T30 Torx screwdriver, remove the single screw connecting the coils to the power supply.
Remove the latches on the coils (the latches are broken on ours) by pushing the coil tabs in using a spudger.
Remove the coil by holding the plug back and pulling it out.
Put these coils aside to be replaced later.

Step 8

Repair step

⌕

TOOL USED ON THIS STEP T30 Torx Screwdriver Bit Referenced by the iFixit guide

View item

Use a 3/8" ratchet wrench with a 5/8" (16 mm) spark-plug socket to loosen the spark plug counterclockwise. Firm force may be required.
Finish unscrewing the spark plug by hand and remove it.
Safely discard the old spark plug.

Step 9

Repair step

⌕

Insert the new spark plug into the spark plug socket tool, ensuring not to insert it too far as to prevent the spark plug from being lodged in the tool.
The spark plug should be secure enough to remain in the socket tool without slipping out, but not too tight such that the spark plug cannot be removed.
Make sure, while inserting the new spark plug into the engine where the coils were removed, to twist without pushing down onto the socket excessively.
Using the torque wrench, torque the spark plugs up to 25 Newton-meters (Nm) or 22 foot-pounds (ft-lbs).
Repeat steps 7 to 9 with the remaining spark plugs if necessary.

Step 10

Repair step

⌕

TOOL USED ON THIS STEP Metal Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP T30 Torx Screwdriver Bit Referenced by the iFixit guide

View item

Reinstall the ignition coils by pushing each coil straight down until seated.
Reconnect the connector clips until they click.
Replace the screw connecting the coil screws to the power source that was removed previously.

Step 11

Repair step

⌕

TOOL USED ON THIS STEP Metal Spudger Referenced by the iFixit guide

View item

Reinstall the engine cover by aligning it and press down at the rear and front until both clips snap into place.

Step 12

Repair step

⌕

TOOL USED ON THIS STEP Metal Spudger Referenced by the iFixit guide

View item

Locate the battery’s negative (–) post in the innermost right corner of the trunk.
Place the negative (–) cable clamp back onto the post, seating it fully.
Tighten the clamp’s 10 mm bolt clockwise until snug.

Step 13

Repair step

⌕

TOOL USED ON THIS STEP Metal Spudger Referenced by the iFixit guide

View item

Replace the trunk panel covering the battery compartment.

Step 14

Repair step

⌕

TOOL USED ON THIS STEP Metal Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP T30 Torx Screwdriver Bit Referenced by the iFixit guide

View item

Replace the spare tire and secure it with the included screw top.
Lower the trunk floor panel to hide the spare tire.
Close both the hood and the trunk of the car.
Start the engine to ensure proper installation.
(Optional): Connect an On Board Diagnostic tool to make sure your car isn't misfiring