(New) iPhone 15 Screen Installation (for Logic Board)

Step 1

Remove the screen adhesive

⌕

• Be careful not to damage any of the spring contacts as you clean the frame.
• This is a good point to test your repair before sealing up your phone. Connect the screen, power on your phone, and make sure it works as expected. Power it back down and continue reassembly.
• The adhesive remaining on your phone is difficult to remove and leaves residue. If you have trouble removing the adhesive, apply some heat using a hair dryer or heat gun.
• Use a spudger to push the screen adhesive up until you can grab it with a pair of tweezers.
• Use a pair of tweezers, or your fingers, to remove the adhesive around the entire perimeter of the iPhone.

Step 2

Repair step

⌕

• Any leftover residue will compromise your iPhone's seal. Be sure to clean the frame thoroughly.
• Wrap a microfiber or lint-free cloth around the pointed end of a spudger and apply a few drops of high-concentration (greater than 90%) isopropyl alcohol to the cloth.
• Wipe in one direction along the perimeter of the frame to clean the adhesive residue.
• Wait a few minutes before proceeding to make sure any excess alcohol has evaporated.

Step 3

Orient the adhesive

⌕

• Lay the adhesive next to the phone and use features like cutouts for spring contacts and the front‑facing camera to make sure the adhesive is oriented correctly.
• Your adhesive may look slightly different.

Step 4

Apply the adhesive

⌕

• Once the adhesive is pressed into place, you can't reposition it—you'll have to remove it and start over with new adhesive.
• Use the pull tab to begin peeling the back liner off of the adhesive starting from the bottom, but do not remove the liner all the way.
• While holding the back liner out of the way, carefully align the exposed edge of the adhesive to the bottom edge of the iPhone's frame.

Step 5

Repair step

⌕

• When the adhesive is aligned, use the flat end of a spudger, or your finger, to press it down firmly along the bottom edge.

Step 6

Repair step

⌕

• Continue peeling the back liner off of the adhesive while pressing the adhesive into place along the edges of the iPhone's frame.
• If you correctly aligned the lower edge of the adhesive, the side and top edges will fall perfectly into place. If the adhesive is misaligned, remove it and start over with new adhesive.
• If your adhesive is misaligned and you don't have another set handy, it's okay to temporarily put your iPhone back together and use it normally without any adhesive, but keep in mind that your iPhone's water resistance will be compromised until you install new adhesive.

Step 7

Press the adhesive into place

⌕

• Make sure the liner is aligned properly by checking that all spring contacts and the front-facing camera are in their cutouts. If they aren't, remove the adhesive and start over with a new sheet.
• Use the flat end of a spudger to press the adhesive firmly into place all around the iPhone.
• Be careful not to press on the camera, spring contacts, or other internal components.

Step 8

Remove the top liner

⌕

• Insert the point of a spudger under the top liner's hole at the bottom of the frame.
• Pry up to separate the liner from the frame—enough to grip it with your fingers.
• Your pull tab may be in a different location. Make sure you're pulling the full-size top liner, not the thin liners under it.

Step 9

Repair step

⌕

• Peel back the top liner and remove it.

Step 10

Prop up the screen

⌕

• Prop the screen up along the left edge of the iPhone frame, using a box or similar sturdy object to support the screen.

Step 11

Connect the screen

⌕

• Use the flat end of a spudger or your finger to connect the screen and front sensor press connectors.

Step 12

Repair step

⌕

• Insert the top of the screen connector cover into its slot in the frame and lay it over the press connector.

Step 13

Repair step

⌕

• Insert the front sensor connector cover into its slot in the frame at a 90‑degree angle vertically.
• Lay the cover over the press connector.

Step 14

Install the cover screws

⌕

• Use a tri-point Y000 driver to install the two 0.9 mm‑long screws securing the front sensor connector and screen connector covers.

Step 15

Remove the final adhesive liners

⌕

• As you remove the liners in this step, the adhesive will be fully exposed. Make sure nothing touches the exposed adhesive.
• Use a spudger, or your fingers, to separate the pull tabs at the bottom right corner of the frame.

Step 16

Repair step

⌕

• Remove the narrow liner covering the adhesive along the right and top edges of the frame.

Step 17

Repair step

⌕

• Remove the liner along the bottom edge of the frame.

Step 18

Repair step

⌕

• Without letting the screen touch the adhesive, hold the screen over the phone so you can access the final liner along the left edge of the phone.
• Use a pair of tweezers or your fingers to remove the final liner along the left edge of the phone.

Step 19

Place the screen

⌕

• Lay the screen straight down onto the frame and press until the clips engage.
• Press around the perimeter of the screen to engage all clips.

Step 20

Heat the screen

⌕

• To help the adhesive bond, apply heat to the edges of the screen using an iOpener, hair dryer, or heat gun until it's hot to the touch.
• If you have screen vise clamps, use them to strengthen the bond of your new adhesive. If not, keep reading for more ways to secure the screen.

Step 21

Press the screen

⌕

• To evenly compress your iPhone and strengthen the bond of the screen to the frame, you need to account for the camera bump.
• If you have the box your iPhone came in, take the lid and place it on a flat surface.
• If you don't have your original box, skip this step for an alternate method.
• Place your iPhone screen-side-up in the lid of your box with the camera bump in its recess.
• Find something close to the size of your iPhone, but taller than the sides of the box. Stack it on top of the iPhone, followed by a few heavy objects.
• Leave the objects in place for at least thirty minutes. The lighter the objects, the longer they should be left. Ideally, leave them stacked overnight.

Step 22

Repair step

⌕

• If you don't have the original box for your iPhone, follow the next three steps for another method to evenly compress the screen.
• Place the iPhone screen-side-down on a soft, flat surface.
• Apply tape to the back glass to protect its finish.

Step 23

Repair step

⌕

• Place evenly spaced layers of coins or similarly thick objects on the tape along the edges of the back glass.
• Stack them to a consistent height taller than the camera bump.

Step 24

Repair step

⌕

• Stack multiple books or other heavy objects on your iPhone.
• The coins may leave an impression on the bottom object, so don't use anything valuable.
• Leave the objects in place for at least thirty minutes. The lighter the objects, the longer they should be left. Ideally, leave them stacked overnight.