iPhone 17 Pro Logic Board Intermediate Installation

Step 1

Install the logic board

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

• Use an opening pick to hold the flex cables along the left edge of the iPhone to prevent them from being trapped underneath the logic board.
• Swing the logic board down in place, making sure no flex cables are trapped along the left and bottom edges.

Step 2

Repair step

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

• Check the right edge of the logic board to make sure the power button connector wasn't trapped underneath the logic board.

Step 3

Repair step

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

• Use your finger to press and connect the small button connector on the left side of the logic board.
• Stop if the connector feels like it won't reach. The button cable has a bend that often catches underneath the logic board. Lift the logic board, free the cable bend, and try again.

Step 4

Repair step

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

• Use your finger to press and attach the six press connectors:
• Two connectors along the top edge of the logic board
• One remaining button board connector
• Two USB-C port assembly connectors (one on top of the other)
• One power button connector

Step 5

Install the button connector cover

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

• Latch the end of the button connector cover onto the logic board.

Step 6

Repair step

⌕

TOOL USED ON THIS STEP JIS 00 Screwdriver Bit Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• Use a tri-point Y000 screwdriver to install the 1.0 mm‑long button connector screw.

Step 7

Install the top speaker

⌕

• Align the top edge of the top speaker with the iPhone.
• Lay the speaker in its recess.

Step 8

Repair step

⌕

TOOL USED ON THIS STEP JIS 00 Screwdriver Bit Referenced by the iFixit guide

View item

• Use a JIS 00 screwdriver to install the three 2.2 mm‑long top speaker screws.

Step 9

Install the front camera assembly

⌕

• Lay the front camera assembly in its recess.

Step 10

Repair step

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

• Use your fingers to press and connect the two front camera assembly connectors.

Step 11

Install the front camera connector cover

⌕

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide

View item

• Hook the small latch in the corner of the camera connector cover onto the logic board and set it in place.

Step 12

Repair step

⌕

TOOL USED ON THIS STEP JIS 00 Screwdriver Bit Referenced by the iFixit guide

View item

TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide

View item

• Use a tri-point Y000 screwdriver to install the 1.0 mm‑long front camera connector screw.