FIXONIC
Repair starts here.Sign inCreate account Live auctionsRepair HubRepair guides
SellSavedMy Fixonic
FIXONICrepair marketplace
Home/ Repair guides/ iPhone 17 Pro Front Camera Assembly Replacement
Official iFixit API visual reference

iPhone 17 Pro Front Camera Assembly Replacement

Follow this guide to replace the front camera...

Apple iPhone 17 Pro Moderate 1 - 2 hours Guide 207490
Open the authorised source
Licensed iFixit integration

This attributed iFixit guide is displayed through Fixonic's recorded commercial API permission. iFixit remains the independent source and author of the procedure.

Guide overview

Before you begin

Follow this guide to replace the front camera assembly in an iPhone 17 Pro. If your front-facing photos come out fuzzy, noisy, or your camera has trouble focusing, it might need to be replaced. The front camera assembly includes the front-facing camera and Face ID hardware. After your repair, calibrate Apple front cameras using Repair Assistant.

Step 1

Safety precautions

iPhone 17 Pro Front Camera Assembly Replacement — Safety precautions ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Let your iPhone's battery drain below 25% before starting this repair—a charged lithium‑ion battery may catch fire if damaged.
  • Unplug all cables from your phone.
  • Hold the power and either volume button and slide to power off your phone.
Step 2

Cracked glass preparation

iPhone 17 Pro Front Camera Assembly Replacement — Cracked glass preparation ⌕
Safety Glasses
TOOL USED ON THIS STEP Safety Glasses Referenced by the iFixit guide
View item
Suction Handle
TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide
View item
  • Glass shards can complicate disassembly—or worse, cause injury. If your phone is cracked, follow this step.
  • Apply strips of packing tape to the cracked glass until it's completely covered—this will help keep the glass contained and allow the suction cup to stick.
  • Make sure there's a single strip of tape (not overlapping) across the bottom edge, big enough for a suction cup to fit on.
  • Only cover the glass itself—don't stick any tape to the frame.
  • Consider wearing safety glasses to protect your eyes from any glass shaken free during the repair.
Step 3

Remove the pentalobe screws

iPhone 17 Pro Front Camera Assembly Replacement — Remove the pentalobe screws ⌕
4IP Torx Plus Bit
TOOL USED ON THIS STEP 4IP Torx Plus Bit Referenced by the iFixit guide
View item
JIS 00 Screwdriver Bit
TOOL USED ON THIS STEP JIS 00 Screwdriver Bit Referenced by the iFixit guide
View item
  • Use a P2 pentalobe screwdriver to remove the two 7.5 mm‑long screws on either side of the charging port.
Step 4

Mark your opening picks

iPhone 17 Pro Front Camera Assembly Replacement — Mark your opening picks ⌕
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • If inserted too far, an opening pick can damage your device. Follow this step to mark your pick and prevent damage.
  • Measure 3 mm from the tip and mark the opening pick with a permanent marker.
  • Alternatively, you can tape a coin 3 mm from the tip of the pick.
Step 5

Heat the bottom edge

iPhone 17 Pro Front Camera Assembly Replacement — Heat the bottom edge ⌕
Heat Gun
TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide
View item
  • Use a hair dryer or heat gun to heat the bottom edge of the screen until it's slightly too hot to touch.
  • Improper use of a heat gun can destroy the display and/or battery—follow the linked instructions carefully.
Step 6

Apply a suction handle

iPhone 17 Pro Front Camera Assembly Replacement — Apply a suction handle ⌕
Suction Handle
TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide
View item
  • Apply a suction handle to the bottom edge of the screen, as close to the edge as possible.
Step 7

Screen bezel information

iPhone 17 Pro Front Camera Assembly Replacement — Screen bezel information ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • During the next step, make sure you're inserting your pick in the correct location:
  • There's a plastic bezel on the underside of the screen that sits on the frame. Insert your pick here, making sure it's completely under the bezel.
  • There's a seam between the plastic bezel and the display panel. Don't insert your pick here or you'll separate the two, complicating the repair.
Step 8

Insert an opening pick

iPhone 17 Pro Front Camera Assembly Replacement — Insert an opening pick ⌕
Suction Handle
TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • Pull up on the suction handle with strong, steady force until a gap forms between the screen and frame.
  • This may take significant force. If you're having trouble, reheat the screen and try again.
  • Insert the tip of an opening pick in the gap you just created.
Step 9

Screen information

iPhone 17 Pro Front Camera Assembly Replacement — Screen information ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Don't insert your pick more than 3 mm under the screen to avoid damaging the following components:
  • The screen and ambient light sensor cables are located near the volume and Action buttons.
  • There are delicate spring contacts around the perimeter of the phone.
  • The underside of the screen has thin, metal clips that go into corresponding slots on the frame.
Step 10

Separate the bottom edge adhesive

iPhone 17 Pro Front Camera Assembly Replacement — Separate the bottom edge adhesive ⌕
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • Slide the opening pick along the bottom edge to separate the adhesive.
  • Leave the pick inserted under the bottom right corner to prevent the adhesive from re‑sealing.
Step 11

Remove the suction handle

iPhone 17 Pro Front Camera Assembly Replacement — Remove the suction handle ⌕
Suction Handle
TOOL USED ON THIS STEP Suction Handle Referenced by the iFixit guide
View item
  • Pull the small nub on the suction cup to remove it from the screen.
Step 12

Heat the right edge

iPhone 17 Pro Front Camera Assembly Replacement — Heat the right edge ⌕
Heat Gun
TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide
View item
  • Use a hair dryer or heat gun to heat the right edge of the screen until it's slightly too hot to touch.
Step 13

Separate the right edge adhesive

iPhone 17 Pro Front Camera Assembly Replacement — Separate the right edge adhesive ⌕
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • Insert a second opening pick under the bottom right corner of the screen.
  • Slide the pick up the right edge to separate the adhesive and release the two clips.
  • You may need to pry the screen up slightly to release the clips
  • Leave the pick inserted under the top right corner to prevent the adhesive from re‑sealing.
Step 14

Heat the top edge

iPhone 17 Pro Front Camera Assembly Replacement — Heat the top edge ⌕
Heat Gun
TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide
View item
  • Use a hair dryer or heat gun to heat the top edge of the screen until it's slightly too hot to touch.
Step 15

Separate the top edge adhesive

iPhone 17 Pro Front Camera Assembly Replacement — Separate the top edge adhesive ⌕
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • Insert a third opening pick under the top right corner of the screen.
  • Slide the pick along the top edge and just barely around the top left corner to separate the adhesive and release the two clips.
  • Don't slide the pick farther, or you may damage the ambient light sensor cable.
  • Leave the pick inserted under the top left corner to prevent the adhesive from re‑sealing.
Step 16

Heat the left edge

iPhone 17 Pro Front Camera Assembly Replacement — Heat the left edge ⌕
Heat Gun
TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide
View item
  • Use a hair dryer or heat gun to heat the left edge of the screen until it's slightly too hot to touch.
Step 17

Separate the left edge adhesive

iPhone 17 Pro Front Camera Assembly Replacement — Separate the left edge adhesive ⌕
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • Insert a fourth opening pick under the bottom left corner of the screen.
  • Slide the pick up the right edge to separate the adhesive and release the clip, stopping just before the volume up button.
  • You may need to pry up the screen slightly to release the clip.
  • Don't slide the pick farther, or you may damage the screen cable.
Step 18

Prop up the screen

iPhone 17 Pro Front Camera Assembly Replacement — Prop up the screen ⌕
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • At this point, the screen should be completely detached from the frame. If it feels stuck, go back around the perimeter and separate any remaining adhesive or clips.
  • Lift the screen straight up and swing it over the left edge, propping it up against a sturdy box or stack of books so the cables aren't strained.
  • Alternatively, you can lay the screen down flat over the left side.
Step 19

Remove the cover screws

iPhone 17 Pro Front Camera Assembly Replacement — Remove the cover screws ⌕
4IP Torx Plus Bit
TOOL USED ON THIS STEP 4IP Torx Plus Bit Referenced by the iFixit guide
View item
JIS 00 Screwdriver Bit
TOOL USED ON THIS STEP JIS 00 Screwdriver Bit Referenced by the iFixit guide
View item
  • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.
  • Use a JIS 00 screwdriver to remove the two screws securing the cable covers:
  • One 1.4 mm‑long screw for the screen and front sensor cable cover
  • One 1.3 mm‑long screw for the battery cover
  • Small iFixit Phillips bits are designed to work with JIS screws. You can try Phillips drivers from other manufacturers, but you risk stripping the screw.
Step 20

Remove the covers

iPhone 17 Pro Front Camera Assembly Replacement — Remove the covers ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • Remove the two covers.
Step 21

Disconnect the battery

iPhone 17 Pro Front Camera Assembly Replacement — Disconnect the battery ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use the point of a spudger to pry up and disconnect the battery press connector.
Step 22

Disconnect the screen

iPhone 17 Pro Front Camera Assembly Replacement — Disconnect the screen ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • Use the tip of an opening pick or the point of a spudger to pry up and disconnect the screen and ambient light sensor press connectors.
Step 23

Remove the screen

iPhone 17 Pro Front Camera Assembly Replacement — Remove the screen ⌕
  • Remove the screen.
Step 24

Remove the battery tray screws

iPhone 17 Pro Front Camera Assembly Replacement — Remove the battery tray screws ⌕
4IP Torx Plus Bit
TOOL USED ON THIS STEP 4IP Torx Plus Bit Referenced by the iFixit guide
View item
JIS 00 Screwdriver Bit
TOOL USED ON THIS STEP JIS 00 Screwdriver Bit Referenced by the iFixit guide
View item
  • Use a Torx Plus 4IP screwdriver to remove the screws securing the battery tray:
  • One 7.5 mm‑long screw
  • One 5.9 mm‑long screw
  • One 3.4 mm‑long screw
  • One 2.3 mm‑long screw
  • Nine 3.7 mm‑long screws
  • One 3.7 mm‑long screw
  • iPhone models with a physical SIM card won't have this screw.
Step 25

Remove the battery

iPhone 17 Pro Front Camera Assembly Replacement — Remove the battery ⌕
  • Use your finger to lift the top left corner of the battery tray and remove it.
  • Be careful not to smudge the front camera.
Step 26

Remove the front camera connector cover

iPhone 17 Pro Front Camera Assembly Replacement — Remove the front camera connector cover ⌕
4IP Torx Plus Bit
TOOL USED ON THIS STEP 4IP Torx Plus Bit Referenced by the iFixit guide
View item
JIS 00 Screwdriver Bit
TOOL USED ON THIS STEP JIS 00 Screwdriver Bit Referenced by the iFixit guide
View item
  • Use a tri-point Y000 screwdriver to remove the 1.0 mm‑long screw securing the front camera connector cover.
Step 27

Repair step

iPhone 17 Pro Front Camera Assembly Replacement — repair step ⌕
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • Use tweezers to unhook and remove the front camera connector cover.
Step 28

Remove the front camera assembly

iPhone 17 Pro Front Camera Assembly Replacement — Remove the front camera assembly ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use the point of a spudger to pry up and disconnect the two front camera connectors (one's under the other) from the logic board.
Step 29

Repair step

iPhone 17 Pro Front Camera Assembly Replacement — repair step ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • Use the point of a spudger to pry up the right edge of the front camera assembly.
  • Lift and remove the front camera assembly from its recess.
Step 30

Disassembly complete

iPhone 17 Pro Front Camera Assembly Replacement — Disassembly complete ⌕
  • Congratulations on completing disassembly! The remaining steps will show how to reassemble your iPhone.
  • Depending on your iPhone model, some reassembly photos may have minor visual discrepancies. The procedure, however, will be correct for your iPhone.
Step 31

Install the front camera assembly

iPhone 17 Pro Front Camera Assembly Replacement — Install the front camera assembly ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Place the front camera assembly in its recess and carefully guide its cables into the groove.
Step 32

Repair step

iPhone 17 Pro Front Camera Assembly Replacement — repair step ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use your fingers to carefully align and press the two front camera assembly press connectors onto the logic board.
Step 33

Install the front camera connector cover

iPhone 17 Pro Front Camera Assembly Replacement — Install the front camera connector cover ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Hook the camera connector cover onto the logic board and set it in place.
Step 34

Repair step

iPhone 17 Pro Front Camera Assembly Replacement — repair step ⌕
4IP Torx Plus Bit
TOOL USED ON THIS STEP 4IP Torx Plus Bit Referenced by the iFixit guide
View item
JIS 00 Screwdriver Bit
TOOL USED ON THIS STEP JIS 00 Screwdriver Bit Referenced by the iFixit guide
View item
  • Use a tri-point Y000 screwdriver to install the 1.0 mm‑long screw to secure the front camera connector cover.
Step 35

Install the battery

iPhone 17 Pro Front Camera Assembly Replacement — Install the battery ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Lay the battery tray in place.
  • Make sure not to trap any cables underneath the tray.
Step 36

Install the battery tray screws

iPhone 17 Pro Front Camera Assembly Replacement — Install the battery tray screws ⌕
4IP Torx Plus Bit
TOOL USED ON THIS STEP 4IP Torx Plus Bit Referenced by the iFixit guide
View item
JIS 00 Screwdriver Bit
TOOL USED ON THIS STEP JIS 00 Screwdriver Bit Referenced by the iFixit guide
View item
  • Use a Torx Plus 4IP screwdriver to install the battery tray screws:
  • One 7.5 mm‑long screw
  • One 5.9 mm‑long screw
  • One 3.4 mm‑long screw
  • One 2.3 mm‑long screw
  • Nine 3.7 mm‑long screws
  • One 3.7 mm‑long screw
  • iPhone models with a physical SIM card won't have this screw.
Step 37

Clean the frame

iPhone 17 Pro Front Camera Assembly Replacement — Clean the frame ⌕
Heat Gun
TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide
View item
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • Work around the fragile grounding clips as you clean the frame. If you bend one out of place, gently bend it back with your fingers or tweezers.
  • Use tweezers or your fingers to remove large pieces of adhesive from the frame perimeter.
  • Use a spudger to scrape the adhesive residue off the frame.
  • If the adhesive feels stubborn, apply some heat using a hair dryer or heat gun and try again.
Step 38

Repair step

iPhone 17 Pro Front Camera Assembly Replacement — repair step ⌕
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • Use a lint-free cloth or a coffee filter to wipe in one direction along the perimeter of the frame to clean the adhesive residue.
  • If the residue feels sticky, apply a few drops of isopropyl alcohol to the cloth and wipe again.
  • Take your time doing this. A clean frame allows replacement adhesive to lay evenly, ensuring a better bond.
Step 39

Clean the screen

iPhone 17 Pro Front Camera Assembly Replacement — Clean the screen ⌕
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • If you're reusing your screen, apply a few drops of highly-concentrated isopropyl alcohol (over 90%) to a microfiber or lint-free cloth and wipe around the perimeter to prepare the surface for new adhesive.
Step 40

Orient the replacement adhesive

iPhone 17 Pro Front Camera Assembly Replacement — Orient the replacement adhesive ⌕
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • Without peeling any liners, lay the adhesive sheet over the frame to determine its proper orientation.
  • Use features such as the camera cutout and notches along the top and bottom edges to visualize how the adhesive will lay in the frame.
Step 41

Apply the replacement adhesive

iPhone 17 Pro Front Camera Assembly Replacement — Apply the replacement adhesive ⌕
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • Grab the tab in the corner of the adhesive sheet and peel the liner to expose a third of the adhesive.
  • The exposed adhesive is very sticky. Don't let it touch anything until you're ready to apply it to the frame.
  • If your adhesive has multiple liners, peel the liner that exposes the side that sticks to the frame.
Step 42

Repair step

iPhone 17 Pro Front Camera Assembly Replacement — repair step ⌕
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • Once the adhesive is pressed into place, you can't reposition it—you'll have to remove it and start over with new adhesive.
  • Carefully align the exposed edge of the adhesive strip with the corresponding edge of the iPhone's frame.
  • When it's correctly aligned, gently press the exposed adhesive strip onto the frame.
Step 43

Repair step

iPhone 17 Pro Front Camera Assembly Replacement — repair step ⌕
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
iFixit Opening Picks (Set of 6)
TOOL USED ON THIS STEP iFixit Opening Picks (Set of 6) Referenced by the iFixit guide
View item
  • Continue peeling away the liner from the adhesive, gently pressing the adhesive into place.
  • If you've correctly aligned the adhesive, the edges will fall perfectly into place.
  • If your adhesive is slightly misaligned, gently pull the long edges into alignment with the frame.
  • If the adhesive begins to crease or wrinkle, remove it and start over with fresh adhesive.
  • If you don't have another set of adhesive strips handy, it's okay to temporarily put your iPhone back together and use it normally without any adhesive. Just keep in mind that your iPhone's water resistance will be compromised until you replace the adhesive.
Step 44

Repair step

iPhone 17 Pro Front Camera Assembly Replacement — repair step ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use a spudger to press the adhesive around the entire perimeter of your iPhone.
  • Work around the fragile grounding clips. If you bend one out of place, gently bend it back with your fingers or tweezers.
  • Don't press too hard, or you'll stretch and deform the adhesive.
Step 45

Repair step

iPhone 17 Pro Front Camera Assembly Replacement — repair step ⌕
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
  • Use the pull tab to peel off the large front liner from the adhesive. The pull tab is often in a corner of the liner.
  • At this point, you'll still have liners covering the perimeter. Don't remove these liners yet—they prevent the adhesive from accidentally sticking while you reassemble your iPhone.
Step 46

Connect the screen

iPhone 17 Pro Front Camera Assembly Replacement — Connect the screen ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Set the iPhone screen next to the frame such that the screen cables can comfortably reach the logic board.
Step 47

Repair step

iPhone 17 Pro Front Camera Assembly Replacement — repair step ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use your finger or the flat end of a spudger to press and connect the two screen connectors onto the logic board.
  • Don't try to force the connector into place. If you're having trouble, reposition it and try again.
Step 48

Connect the battery

iPhone 17 Pro Front Camera Assembly Replacement — Connect the battery ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Use your finger or the flat end of a spudger to press and connect the battery connector onto the logic board.
Step 49

Test your repair

iPhone 17 Pro Front Camera Assembly Replacement — Test your repair ⌕
  • This is a good point to test your repair before sealing up your iPhone. Power on your iPhone and make sure it works as expected. Power it back down and continue reassembly.
  • If your iPhone doesn't turn on, connect it to a power source and try again.
Step 50

Install the battery connector cover

iPhone 17 Pro Front Camera Assembly Replacement — Install the battery connector cover ⌕
4IP Torx Plus Bit
TOOL USED ON THIS STEP 4IP Torx Plus Bit Referenced by the iFixit guide
View item
JIS 00 Screwdriver Bit
TOOL USED ON THIS STEP JIS 00 Screwdriver Bit Referenced by the iFixit guide
View item
  • Tuck the top edge of the battery connector cover under the cutout lip.
  • Make sure both tabs are tucked under the lip.
  • Align the cover by its screw hole and lay it in place.
Step 51

Repair step

iPhone 17 Pro Front Camera Assembly Replacement — repair step ⌕
4IP Torx Plus Bit
TOOL USED ON THIS STEP 4IP Torx Plus Bit Referenced by the iFixit guide
View item
JIS 00 Screwdriver Bit
TOOL USED ON THIS STEP JIS 00 Screwdriver Bit Referenced by the iFixit guide
View item
  • Use a JIS 00 screwdriver to install the 1.2 mm‑long screw to secure the battery connector cover.
Step 52

Install the screen connector cover

iPhone 17 Pro Front Camera Assembly Replacement — Install the screen connector cover ⌕
4IP Torx Plus Bit
TOOL USED ON THIS STEP 4IP Torx Plus Bit Referenced by the iFixit guide
View item
JIS 00 Screwdriver Bit
TOOL USED ON THIS STEP JIS 00 Screwdriver Bit Referenced by the iFixit guide
View item
  • Tuck the left edge of the screen connector cover under the cutout lip.
  • Align the cover by its screw hole and lay it in place.
Step 53

Repair step

iPhone 17 Pro Front Camera Assembly Replacement — repair step ⌕
4IP Torx Plus Bit
TOOL USED ON THIS STEP 4IP Torx Plus Bit Referenced by the iFixit guide
View item
JIS 00 Screwdriver Bit
TOOL USED ON THIS STEP JIS 00 Screwdriver Bit Referenced by the iFixit guide
View item
  • Use a JIS 00 screwdriver to install the 1.2 mm‑long screw to secure the screen connector cover.
Step 54

Remove the final adhesive liners

iPhone 17 Pro Front Camera Assembly Replacement — Remove the final adhesive liners ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • With one hand hold the screen steady.
  • Use your fingers or a spudger to peel away all perimeter liners, exposing the adhesive.
  • Make sure nothing touches the exposed adhesive.
  • Check the internals for any stray liners and remove them. There should be no liners remaining.
Step 55

Install the screen

iPhone 17 Pro Front Camera Assembly Replacement — Install the screen ⌕
Spudger
TOOL USED ON THIS STEP Spudger Referenced by the iFixit guide
View item
Tweezers
TOOL USED ON THIS STEP Tweezers Referenced by the iFixit guide
View item
  • Lower the screen onto the frame, beginning with the top edge.
  • If you feel resistance, a perimeter clip may have bent out of place and is being crushed by the frame. Look at the point of resistance and gently straighten any bent clips.
  • Make sure the screen edge isn't pinching any cables.
  • Press along the edges of the iPhone until the screen sits flush against the frame.
Step 56

Repair step

iPhone 17 Pro Front Camera Assembly Replacement — repair step ⌕
  • Firmly squeeze around the entire perimeter of the iPhone.
Step 57

Apply heat to the perimeter

iPhone 17 Pro Front Camera Assembly Replacement — Apply heat to the perimeter ⌕
Heat Gun
TOOL USED ON THIS STEP Heat Gun Referenced by the iFixit guide
View item
iF
TOOL USED ON THIS STEP Isopropyl Alcohol (90% or Greater) Referenced by the iFixit guide
View item
  • Use a hair dryer or a heat gun to heat the screen perimeter until it's slightly too hot to touch.
  • The heat softens the adhesive and helps create a better bond.
Step 58

Install the pentalobe screws

iPhone 17 Pro Front Camera Assembly Replacement — Install the pentalobe screws ⌕
4IP Torx Plus Bit
TOOL USED ON THIS STEP 4IP Torx Plus Bit Referenced by the iFixit guide
View item
JIS 00 Screwdriver Bit
TOOL USED ON THIS STEP JIS 00 Screwdriver Bit Referenced by the iFixit guide
View item
  • Use a P2 pentalobe screwdriver to install the two 7.5 mm‑long screws on either side of the charging port.