Home/ Repair guides/ 2015-2017 Toyota Camry Front Bumper Cover Repla…

Official iFixit API visual reference

2015-2017 Toyota Camry Front Bumper Cover Replacement

(1) A cracked or sagging front bumper cover...

iFixit Library 2012-2017 Toyota Camry Easy 45 minutes - 1 hour Guide 247745

Licensed iFixit integration

This attributed iFixit guide is displayed through Fixonic's recorded commercial API permission. iFixit remains the independent source and author of the procedure.

Guide overview

Before you begin

A cracked or sagging front bumper cover after a parking-lot scrape doesn't mean a body-shop bill. On the 2015–2017 Camry this is a driveway job — a handful of bolts and clips, about an hour, and no special tools. The replacement cover used here is a standard primed aftermarket unit — we sourced ours from Parts District's bumper cover collection (this cover commonly fits 2015–2017 Camry — always confirm against your vehicle's exact trim and engine and the product's fitment data before buying). Check your old cover for fog lights and parking sensors before you order — some trims have them, some don't, and the sensor holes differ.

Step 1

Park safely and protect the paint

⌕

Park on a level surface and set the parking brake. Lay an old blanket on the ground in front of the car — the cover will come off, and you don't want it scratched.
You're only swapping the plastic cover: the metal crash bar and any airbag sensors behind it stay put. If the crash bar is bent or a sensor is damaged, stop — that's a professional's job.

Step 2

Open the hood and remove the top fasteners

⌕

Open the hood. Along the top edge of the bumper cover, under the hood lip, there's a row of push clips and 10mm bolts. Pop the clips out with the trim tool and remove the bolts with the 10mm socket. Keep all the hardware together — a cup or magnetic tray earns its keep here.

Step 3

Free the front of the fender liners

⌕

TOOL USED ON THIS STEP Phillips #2 Screwdriver Referenced by the iFixit guide

View item

Turn the steering wheel fully to one side — or jack the front up and set it on jack stands if you want more room. In each front wheel well, remove the Phillips screws and push clips holding the front edge of the fender liner.
You only need to free the front of the liner: pull it back just enough to reach the bolt behind it.

Step 4

Remove the side bumper bolts

⌕

Behind each fender liner is a 10mm bolt where the bumper cover meets the fender. Remove the bolt on each side. This bolt is what holds the cover to the fender — once it's out, the side of the cover is held on by clips alone.

Step 5

Remove the lower splash-shield fasteners

⌕

PART USED ON THIS STEP Front bumper cover Referenced by the iFixit guide

View item

Slide under the front of the car and remove the push clips and 10mm bolts along the bottom edge of the bumper cover and the lower splash shield. There are several — work across the whole width and don't skip the corners.

Step 6

Disconnect the fog lights (if equipped)

⌕

Before the cover can come off, reach behind it and squeeze the release tabs on the fog-light connectors — one per side on trims that have fog lights. If your Camry doesn't have fog lights, skip this step. Don't yank the cover with the connectors still attached.

Step 7

Disconnect the parking sensors (if equipped)

⌕

If your Camry has front parking sensors, unplug each sensor connector from the back of the cover. Note which connector goes where — a quick phone photo now saves a guessing game later. No sensors? Skip ahead.

Step 8

Release the cover from the fenders

⌕

Starting on one side, pull the edge of the bumper cover straight outward from the fender to release the retaining clips. Work from the wheel well toward the headlight. Some resistance is normal — a firm, steady pull beats a hard yank. A yank is how the mounting tabs snap. Repeat on the other side.

Step 9

Pull the cover off the front

⌕

With both sides free, pull the cover straight forward off the front of the car — it slides off its locating pins. Set it face-up on the blanket from Step 1. Look at the crash bar and brackets behind it: if anything metal is bent, stop and consult a professional mechanic.

Step 10

Transfer parts to the new cover

⌕

Move everything from the old cover to the new one: fog-light housings, parking sensors, the lower grille, the tow-hook cover, and the license-plate bracket. Seat each sensor fully in its hole — a loose sensor reads wrong. Test-fit each piece before you carry the cover to the car.

Step 11

Install the new cover (reverse order)

⌕

TOOL USED ON THIS STEP Phillips #2 Screwdriver Referenced by the iFixit guide

View item

Hold the new cover up to the car and reconnect the fog-light and parking-sensor connectors — listen for the click on each. Then slide the cover onto its locating pins and push each side into the fender clips until they seat.
Reinstall the hardware in reverse: side 10mm bolts, wheel-well liner screws and clips, lower clips and bolts, and the top clips and bolts. Snug the bolts — don't over-tighten plastic.

Step 12

Check the fit and test everything

⌕

Close the hood and step back. Check the gaps: even along the headlights, the fenders, and the hood edge. If one side sits high, loosen that side's bolts, reseat the clips, and snug them again.
Test the fog lights and the parking sensors. Then take a short drive and listen for rattles — a loose clip will tell you. If the gaps won't line up or a sensor throws a warning, consult a professional mechanic.